Recent content by JsnSanko

Probably a dumb question. Got my stamp back for my SBR lower, also got my Dead Air Wolfman out of jail. Got the 10” Macon Armory Barrel. Hope this feeds better from Glock Mags than the Faxon Barrel does. So with the (extra provided for enhanced) barrel nut and an enhanced hand guard do...

This is weird. I am a newer hand loader and maybe a little above average shooter. Just got an AR together in .224V. Had first range day with it last weekend. Not a single load I tried shot over an inch. So this sounds like marketing. Most were 0.5-0.7” at 100, and 1-1.2 at 200. I started...

Rifle length. It’s two. One is locking back on the bolt carrier not the bolt. One is as described above and a 6.5CM. The other is .308.

I put a heavy buffer and tubs flat wire spring in tonight and it functions just fine. I am going to call JP next week. Both have JP SCS. I didn’t notice until your picture, and looking at some 15’s the other was not catching on the front of bolt, but the bolt carrier. The JP SCS isn’t...

GGP (Grey Ghost Precision) Billet Set. 15” GGP Hand Guard. JP SCS H2 buffer with spring set. Superlative Adjustable Gas Block (bleed off). Geissele NM Trigger. Proof CF 6.5CM barrel. Fat Bastard Muzzle Brake. Quality build………. But skimped money and bought Areo BCG. Have tried 4 different...

I am rolling my own. I will try the stiffer spring and add a heavy buffer then. I am rolling my own. 26gr CFE223 and an 80/80.5 Berger or ELDM was what I was shooting. I have 90 Berger’s and 88 ELDMs also. Thanks for the advice

What set up are people using to go from 80-90gr Berger’s, or Hornady ELDM’s. New build and struggling with pressure signs and cycling issues. I have all the springs and extra Heavy and Steel weights. Thanks in advance for the help. Build is a Mega Set. CLE +2 Bartlien Barrel. Aero...

So I have been playing with triggers lately trying to shrink groups. This means for me swapping some triggers back and forth between rifles. My triggers that I have been working with: Geissele National Match High Speed Geissele SSA-E Geissele G2S Larue MBT-2S RRA National Match Varmint Not...

I like the “whoops” kit they offer also. For just milspec they are fairly local to me and have a large stocking dealer. Can always get what I want, with a veterans discount, and not wait.

Thanks. That cost me my gun allowance. I like the MAD flip up sites. Had to get a set and a rail to try on a build.

What’s wrong with them when you get them minus the FCG? It’s a bag of small parts and springs at that point (yes plus mag release and last round hold open also). They are a totally mil spec kit. I install them even into higher brand billet uppers (LMT and GGP). But I only run Geissele or...

Agree with a lot of people above. Whatever I can get without a trigger and grip. For me Inhave a local dealer that stocks a lot of Aero stuff. I always have a few “whoops” parts kits on hand at home also. That’s for when you shoot a tiny spring across the room. Buy one of each. Pick your...

Top firearm, Vortex Viper PST 3-15x44 SFP on a small frame .224V build. I like this for size. This has a Bartlien Barrel in an Aero set, Larue MBT-2S trigger. Bottom firearm, Nightforce SHV 5-20x56 SFP on a large frame 6.5CM build. Swapping this to my .22 trainer for a Vortex Viper PST Gen 2...

What is the rail used to mount these two scopes? I like that it lets you lower the scope to the bore line by using regular rings. Thanks in advance. I couldn't see markings on either one. Nice rigs.

Have you taken it apart, fully lubricated it, I mean oil the hell out of it, and run it for a while. Large frame ARs need lots of lube and break in. I had this same problem with a higher priced BCG. That’s what I did to fix it. You also didn’t mention which level of BCG as far as finish...