• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by McHaggis

  1. M

    What did you do in the reloading room today?

    I call mine a Wheeler, level, level not level. For obvious reasons. I not longer use it.
  2. M

    Just paid for my Auto Trickler V3, what Area 419 goodies should I get?

    There is another way…
  3. M

    Lee APP and bulge busting 9mm cases. Head first.

    I’ve just recieved my Lee APP press and like everyone I was surprise just how small they are. More of a press-ette than a press to be sure. After mucking around with it I’m wondering if you can bulge bust 9mm cases head first so I can feed it with my case feeder. I’m just too lazy to fill the...
  4. M

    Fx120i scale

    This guy has. Maybe Adam needs to do a v4.
  5. M

    Reloading... finally popped my cherry !

    ADI 2206H is Hogdgon H4895. With 55's I normally use BM2 (Hodgdon Benchmark) but I used to get great results with the old 2206.
  6. M

    Reloading Jams

    80’s & 90’s classic rock on YouTube. A little too loud!
  7. M

    Tumbler only?

    I’ve always used a Lyman 1200 tumbler with walnut and was never that impressed until I started using polish in it with meths to help disperse it. Now I get nice clean cases in 2 hours and no wet cases to deal with.
  8. M

    Recommended reloading dies for 6.5 creedmore (PRS)

    This.... but I also run a mandrel to finalise neck size just prior to bullet seating.
  9. M

    NOOB needing help on reloading equipment

    Good move on the Lyman and a great price. Where I am they are $530 plus shipping. I’m pleased you’re buying bits n pieces rather than a kit for the reasons everyone else has already stated. One thing for sure is that as you get into this and learn more and your process and therefore the kit...
  10. M

    What did you do in the reloading room today?

    Fabbed up my version of an In-line Fab Ergo handle for my LNL AP Press.
  11. M

    Run Out problems I give up......

    My Forster Micro Seater does the same thing. The best way I’ve found to minimise it is to start the bullet into the case a wee bit then stop, lower the ram and rotate the case 180° then continue to fully seat. This reduces runout from 4, 5 or 6 thou down to 1 or 2. I always thought Forster were...
  12. M

    Magnetospeed V3 or Labradar?

    It seems the main con with the MS is POI change. So if it was mounted off the barrel wouldn’t the MS give you the best of both worlds?
  13. M

    Reloading press confessions...Dumb ass move while at the press.

    I annealed about 20 primed cases once. Not one went off thank F. Realised later how lucky I was.
  14. M

    Need 6.5 Creedmore loading Data !

    I’m not sure that’s right. If you do a load work up to find maximum pressure you’ll often find a good node below that at 98% of the max load. Not saying that’s the way to settle on a load but look at your results once load development is complete and see what the % is.
  15. M

    What did you do in the reloading room today?

    Unpacked my new Hornady LnL AP press and decided not to mount it in my current reloading space. The kitchen! Now to build that new bench once I can get the basement dry.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts