• Winner! Quick Shot Challenge: Caption This Sniper Fail Meme

    View thread

Recent content by NDT_Trainer

  1. NDT_Trainer

    Desert Tech MDR

    I have the new gas port on order. I agree is should have been given to MDR owners to help elevate issues. But I guess 50% off is the best they can do. To get around removing the hand guard I just built a little wrench like for a sprinkler valve. Works great I can adjust port with hand guard...
  2. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    PM Sent Quote Originally Posted by kgreylgrey "Thanks. Since I don't plan on shooting past 1000yd - will I'll need any built in elevation? I have the mil version S&B 5x25 scope. "
  3. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    I use this mount (no built in elevation) with a VORTEX RAZOR 5-20 on my SRS in .338 LM. Works fine, no zero shift. I ended up putting a 20 MOA badger rail section on to get a little more vertical adjustment in my glass.
  4. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Here is my .260 load with RL17. Gun DTA SRS Cal. .260 REM Nosler Brass Powder RL-17 GN. 43.8 Bullet Type Sierra HPBT Match King #1740 GN. 140 GR. Velocity: AV 2915 ES 26 SD 11 Temp 79 F Barometer 30.37> R. Humidity 18%
  5. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Congratulations on making the morally correct decision. Just heard the interview on FM105.7.
  6. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Russ, Don't let a few posters cause you to "step back from this thread". I have appreciated what you have posted in the past and look forward to your continued participation here. Thanks.
  7. NDT_Trainer

    Breaking decap pins on .223...?

    I had this issue with some 5.56 crimped brass. I used a universal decapping die and still had some issues due to small flash holes and crimps. So I started to use a "L.E. Wilson Decapping Punch", around $10. I can be a little time consuming but goes pretty quick once you get the hang of using...
  8. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Just wanted to give kudos to the guys at DTA. I had an issue with my Gen 1 .338 LM bolt. Gave DTA a call and had to leave a message. Josh returned my call within an hour. He was very helpful and offered to overnight me a new bolt. Since I kind of wanted to find out why it happened I asked if I...
  9. NDT_Trainer

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Serial Number is on the right side (see photo).
  10. NDT_Trainer

    Share your DTA loads!

    I want to try .308 175 SMK's but I can't get my hands on any. So I did get some Berger VLD Hunting 168 Grain. .308 Win - DTA SRS Winchester Brass CCI-200 Berger VLD 168 Seated to 2.800 42 Gr. Varget MV 2525 ES 10 SD 5 .338 LM - DTA SRS Nosler Brass CCI-250 Berger OTM 250 Grain...
  11. NDT_Trainer

    Ammo temp?

    Not to get to far off the subject or get to technical but I note that some are having trouble with accurate Infra Red thermometer readings. There are several reasons for this. 1st - Some lower cost IR units are only accurate to within +/- 2% of there range. So the larger the range the greater...
  12. NDT_Trainer

    Sig 226 22LR conversion.

    My main defensive pistol is a P226 platinum elite (has short reset trigger) with a SIG factory trigger job. I was looking for a .22 practice pistol and tried a mosquito, don't do it the trigger is terrible and SIG can't do anything for the mosquito's trigger. So I opted for a .22 conversion...
  13. NDT_Trainer

    Free Printable To-Scale Targets

    Impressive. Great resource. I really appreciated the Vortex EBR1 Mrad!
See more
Top Bottom
Back
Home
Forums
Merch
Alerts