• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Recent content by Raivkka

  1. R

    die depth for full length resizing.

    I'll shoot some factory ammo this weekend and take some measurements. I've got a 38 case that looks like it'll work. And, got some additional tools on order at Midway to get the job done correctly. I guess just in time to prep 500 pieces of Lake City brass as well. Guess I know what i'm...
  2. R

    die depth for full length resizing.

    If I put the sizing die all the way down to the shell holder, it creases the casing up by the shoulder. I have to have some space.
  3. R

    die depth for full length resizing.

    Thanks all for the help, I'm really understanding the process a lot more now. 6 or 7 years of reloading for the .308 it was never an issue but this new 6.5 Lothar Barrel is more sensitive. I always thought the full size die automatically set the shoulder at a specific length from the base...
  4. R

    die depth for full length resizing.

    918, I am setting the brass size to the to the full length sizing die as this ammunition is for an AR10/Semi on a 6.5CM, not a bolt action rifle. If I am understanding you correctly.
  5. R

    die depth for full length resizing.

    factory winchester that I bought today for a shoot test is .465. Redding dies and using Sig Brass that I have only shot out of this rifle.
  6. R

    die depth for full length resizing.

    question, when setting the die height, I put my ram all the way up, then screw down the full length resizing die until it touch's the ram and back off 1/2 turn? Is this the correct setting? My reloads are sticking into the chamber where factory ammo is not. The base of my re-sized case...
  7. R

    20” Aero M5 build, have some questions

    I'm using a using a blemished Rubber City BCG with 21" Lothar barrel w/rifle length gas tube and adjustable gas block. Larue trigger. Everything worked with no fussing, just set the gas block. I was actually surprised as I was expecting the worst.
  8. R

    Diamondback/Ruger SR762 upper swap

    At the start there were out of spec uppers. The bolt catch I believe it was. It would fail to hold the bolt back on last round. I could be wrong though. When I got my Ruger they immediately performed a warranty switch and I have never had problems with it. I have also put an Larue 2 stage...
  9. R

    Need Current Armalite AR-10 Guidance

    The only differences between an armalite and dpms is upper receiver rail height, take down pin length, barrel nut threading and gas tube length. I am pretty sure that's it but I could be in error.
  10. R

    Diamondback/Ruger SR762 upper swap

    Be interested to hear how this all works out for you. I have the same rifle and I bought an extra upper and handguard from Matrix Aero several years ago. Haven't built it yet but will someday.
  11. R

    Larue UU kits

    Limited time free assembly by Larue on them at the moment.
  12. R

    For trade, 75gr amax .224, S New Hampshire only

    8/
  13. R

    For trade, 75gr amax .224, S New Hampshire only

    bump
  14. R

    For trade, 75gr amax .224, S New Hampshire only

    bump
  15. R

    Lefty prone shooters - RH/LH bolt?

    Right hand/left eye dom. I bought the stealth BA in 6.5 and it's not a bad rifle. Didn't really want a savage, but after 850 for the rifle and 1000 for the scope, that's a chunk of change. I don't compete, just shoot for fun so really no reason to spend more. PVA is offering the Hancock rifle...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts