• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by rasp65

  1. R

    Red Jacket

    Re: Red Jacket This is how I see the show going. They make so much money from all the "game changers","never bin dun befoe" and opening up new markets" they open up a huge shop. The girl and the father start fighting and eventually split up. The girl opens up her own shop and the fathers...
  2. R

    Flash hole uniforming

    Re: Flash hole uniforming Small flash holes are .060" and would use a 1.5mm drill large flash holes are .080" and I believe that is 2mm.
  3. R

    My seating die removes my bullet

    Re: My seating die removes my bullet With the collet die screwing it down will nt necessarily give you more neck tension. Lee recomends taking out the decapper/mandrel and polishing it down a few thousanths in order to get more tension. I agree with the others about the seating stem try the...
  4. R

    Stainless Steel Media Testimonials

    Re: Stainless Steel Media Testimonials <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Mike Vegas</div><div class="ubbcode-body">I haven't read the entire post yet (7th page) but am I the only one that uses an air compressor to quick dry the brass? I also use the...
  5. R

    Gunsmithing KABOOM Today...with damage, please help.

    Re: KABOOM Today...with damage, please help. I don't see how Model 1 could dispute the use of reloads since there is no commercialy available ammo in 6.5 Sporter or any published load/pressure data available for the cartridge.
  6. R

    Not vendor

    Re: www.carbonarms.us Designed and Built by Shooters Can you buy the JP barrel nut separatly?
  7. R

    How to seat on the lands?

    Re: How to seat on the lands? Take a sized case and put 1 or 2 slits in the neckdown to the shoulder. Clean up the burrs. Place a bullet in the case and leave it long. Place it in the chamber and either close the bolt on it or push it with a dowell until the case shoulder makes contact with...
  8. R

    How to find the best OAL for your gun

    Re: How to find the best OAL for your gun Take a sized case and put 1 or 2 slits in the neckdown to the shoulder. Clean up the burrs. Place a bullet in the case and leave it long. Place it in the chamber and either close the bolt on it or push it with a dowell until the case shoulder makes...
  9. R

    Gunsmithing 6.5-270 wsm??

    Re: 6.5-270 wsm?? Tim How about less than 6 seconds. http://bulletin.accurateshooter.com/2010/11/gone-in-six-seconds-barrel-life/
  10. R

    Gunsmithing Trigger job on an AR15

    Re: Trigger job on an AR15 19 I measured the length in my ar and determined that a 3/8" long 1/4 28 setscrew would fit with my grip screw. I took the pistol grip off, the hammer, trigger and selector. I ran the setscrew up so it was a few threads down and put some loctite on the threads...
  11. R

    AR Phobias from a Bolt Action Guy

    Re: AR Phobias from a Bolt Action Guy Check out these posts in gunsmithing forum http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1943980&gonew=1#UNREAD There is a whole series of threads with ideas on parts to polish that will make your AR alot easier on brass. Adjustable...
  12. R

    375 H&H

    Re: 375 H&H Have not needed to crimp as well. 235 gr to 300 gr even with some heavily compressed loads of IMR 4350.
  13. R

    Neck turning. How thin is too thin?

    Re: Neck turning. How thin is too thin? JWV Like Pete Theodore says you just want to do a clean up on the necks. Start out and work the cutter in until you are cleaning up no more than 80% and go right down to the shoulder.
  14. R

    Gunsmithing Scope Mounting with Epoxy

    Re: Scope Mounting with Epoxy NG As long as the reticle is perfectly vertical and horizontal it certainly will not hurt having the scope locked into the rings with the epoxy. I remember guys using red Loctite in their rings before and I used it to keep my scope from moving on my 375 H&H but...
  15. R

    Seriously! Nobody had an opinion!

    Re: Seriously! Nobody had an opinion! <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Sniper1*</div><div class="ubbcode-body"> I do have a FF tube! The problems seems to be in the flex between the barrel nut and Again, it seems to go back to the FLEX in the...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts