Search results

Re: Red Jacket This is how I see the show going. They make so much money from all the "game changers","never bin dun befoe" and opening up new markets" they open up a huge shop. The girl and the father start fighting and eventually split up. The girl opens up her own shop and the fathers...

Re: Flash hole uniforming Small flash holes are .060" and would use a 1.5mm drill large flash holes are .080" and I believe that is 2mm.

Re: My seating die removes my bullet With the collet die screwing it down will nt necessarily give you more neck tension. Lee recomends taking out the decapper/mandrel and polishing it down a few thousanths in order to get more tension. I agree with the others about the seating stem try the...

Re: Stainless Steel Media Testimonials <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Mike Vegas</div><div class="ubbcode-body">I haven't read the entire post yet (7th page) but am I the only one that uses an air compressor to quick dry the brass? I also use the...

Re: KABOOM Today...with damage, please help. I don't see how Model 1 could dispute the use of reloads since there is no commercialy available ammo in 6.5 Sporter or any published load/pressure data available for the cartridge.

Re: www.carbonarms.us Designed and Built by Shooters Can you buy the JP barrel nut separatly?

Re: How to seat on the lands? Take a sized case and put 1 or 2 slits in the neckdown to the shoulder. Clean up the burrs. Place a bullet in the case and leave it long. Place it in the chamber and either close the bolt on it or push it with a dowell until the case shoulder makes contact with...

Re: How to find the best OAL for your gun Take a sized case and put 1 or 2 slits in the neckdown to the shoulder. Clean up the burrs. Place a bullet in the case and leave it long. Place it in the chamber and either close the bolt on it or push it with a dowell until the case shoulder makes...

Re: 6.5-270 wsm?? Tim How about less than 6 seconds. http://bulletin.accurateshooter.com/2010/11/gone-in-six-seconds-barrel-life/

Re: Trigger job on an AR15 19 I measured the length in my ar and determined that a 3/8" long 1/4 28 setscrew would fit with my grip screw. I took the pistol grip off, the hammer, trigger and selector. I ran the setscrew up so it was a few threads down and put some loctite on the threads...

Re: AR Phobias from a Bolt Action Guy Check out these posts in gunsmithing forum http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1943980&gonew=1#UNREAD There is a whole series of threads with ideas on parts to polish that will make your AR alot easier on brass. Adjustable...

Re: 375 H&H Have not needed to crimp as well. 235 gr to 300 gr even with some heavily compressed loads of IMR 4350.

Re: Neck turning. How thin is too thin? JWV Like Pete Theodore says you just want to do a clean up on the necks. Start out and work the cutter in until you are cleaning up no more than 80% and go right down to the shoulder.

Re: Scope Mounting with Epoxy NG As long as the reticle is perfectly vertical and horizontal it certainly will not hurt having the scope locked into the rings with the epoxy. I remember guys using red Loctite in their rings before and I used it to keep my scope from moving on my 375 H&H but...

Re: Seriously! Nobody had an opinion! <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Sniper1*</div><div class="ubbcode-body"> I do have a FF tube! The problems seems to be in the flex between the barrel nut and Again, it seems to go back to the FLEX in the...

Re: G.F.L 223 Brass? Luke As long as it is a brass case, boxer primed and it is free you will get at least 1 reload out of it, take it and as much as they can give you. Don't forget the donuts and you might have a lifetime supply.

Re: .260 Brass trimming? It would be normal if you use one of these chamber length gauges http://www.sinclairintl.com/.aspx/pid=32925/Product/Sinclair_Chamber_Length_Gage and you keep the case neck off the top of the chamber .005". If you just trim to SAMMI specs then trim back .010" from...

Re: Chambering Issues? LR If you are refering to this http://www.redding-reloading.com/online-catalog/35-competition-shellholder-sets They are all in <span style="font-weight: bold"> </span> + <span style="font-weight: bold"> </span> increments not less than standard thickness.

Re: Souvlaki, Greece's natural super-food Also makes good projectile when you have had way too many.

Re: rebuilding my ar-15 Check Here http://www.ar15.com/forums/topic.html?b=3&f=4&t=226782