• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by thickstrings

  1. T

    Barrel choice...

    I'm about ready for a new project. I have a Rem.700 varmint spec., a older "80's" one, in .243. I want to re-barrel to 6.5Crmr. I have been reading about the Muller barrels and want a opinion on them. Most of my shooting bud's are running Bartlain's. We mostly shoot from the bench at 300 yrds...
  2. T

    Gunsmithing escutchen

    Thanks all....got a guy on accurate shooter.com "preacher" to make me one...its in the mail
  3. T

    Gunsmithing escutchen

    I have asked this before, to no avail...I have built a "bench" stock for a Savage 110. I am in need of a "escutchen for the front screw....Does any know where I can find such a thing? thanks
  4. T

    Rifle Scopes how much up do I need

    I have a question. I am thinking on getting the Sightron S111 10-50x60 scope. The specs. show 50 of elevation. I have a 20moa rail on a Savage110 in 6.5 Creedmoor. The question is, can I get a 100 -200yrd. zero or do I need more elevation? I had a few cheaper 1" scopes on it and I had to aim way...
  5. T

    6 inches low at 15m?!

    You may have the Imfamous Ruger " barrel droop", due to the crappy way the barrel mounts....put a shim, rubber inner tube ect. in the stock to raise the barrel up and or get a Gunsmither V-block... it has a adjustable small screw that pushes the barrel up built in.....Do not over torque your...
  6. T

    Gunsmithing need some help..

    Need some help finding a part. I'm looking for a Bezel?.... eschutchen?.... Fancy ass washer to go on the bottom of a stock, where the take down screw goes through...I have seen it for sale on a site, but damned if I can find it...they were about 20$ has anyone seen this? thanks
  7. T

    First attempts at long range .22LR.. think i need help..

    Don't know what you are shooting off of, but, a sticky front rest will cause vertical inaccuracies.
  8. T

    Ruger Charger 10/22 trouble ….please help

    Try polishing the head of the hammer strut, and make sure that the "C" clip holding the spring is facing up.... Check inside receiver for drag marks from the bolt and polish. I have put a "Q" tip in a cordless drill with a touch of Flitz to polish up a sticky chamber. No problems with my Kidd...
  9. T

    Gunsmithing Rimfire smiths? bedding question, Ruger 77/22

    If it were me, I'd pillar it and bed the first inch or so of the barrel....let it float...ammo could be a factor if throws a flier here and there. Check takedown screw torque?
  10. T

    Gunsmithing savage safety

    You guys will have to wait till I put some more money in it! But I appreciate the offer....I had a scope on it that did'nt have enough adjustment with the 20m rail......aimed at a rock below the target,3 at 100 to zero,[sort of} 3 touching at 300..... Gonna try again with a borrowed scope. Only...
  11. T

    Gunsmithing savage safety

    Have the same problem.Mine is a 80's 110 except that the saftey on mine broke in half,pawn shop gun. Ordered a new one from Gunparts inc. still won't work. the screw for the adjustment is not long enough the affect the saftey with out falling out. 6.5 creed Mc gowan barrel, Rifle basic trigger...
  12. T

    Gunsmithing A little off the beaten path...Pre-64 Winchester 94 Lever Action HELP!

    danthegunman.com - View image galleries Bought a rifle from the guy a few years ago....Good to go...........what you want done is just what he does....
  13. T

    10/22 bedding

    Frequently Asked Questions This is from the Kidd website, scroll down to the barrel section. Also, only 10lbs torque on the v-block screws. I would suggest the Kidd bolt and receiver pins that screw in. The stock stock will be marginal at best,without a pillar. I would look into the rear tang...
  14. T

    fitting tacticool stock to Brno Model 1

    I have googeled 17/22 swager and did'nt find out to much...Could you educate me on the benefits of this change? I don't understand....Are you puting a 17cal. bullet on a .22 rimfire? 17 mach2 is allready out there.....plus a 1 in 8 twist?................ You got my attention with the Brno...
  15. T

    Not tactical in the least my Kimber 82G bench rest rifle

    In case your interested 2 oz. 82G trigger. - RimfireCentral.com Forums
See more
Top Bottom
Back
Home
Forums
Merch
Alerts