• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by ugsly

  1. U

    Gunsmithing Thanks PT&G!

    +1 on what Bohem said. Long ago I got bit by my "Floating" Holder. Casey
  2. U

    Gunsmithing Virgin Brass Failing to Extract

    If its not catching the brass something is wrong. Dont settle with it not running 100%, send it to a good smith and have them fix it. I may be way off but to me it sounds like someone needs to double check some measurments and maybe tweak it some to get proper case protusion so the extractor...
  3. U

    Gunsmithing Chronicle of my first build

    Looks good Cast :) might put a tad more chamfer on your counter bore if you have problems with feeding. Keep up the good work bud. Casey
  4. U

    Gunsmithing Making a muzzle thread protector

    You can buy them for pretty cheap and contour them in. If you wanted to make one you could measure your existing threads on your barrel with a set of wires and make a plug with the exact dimensions. Then when you turn and thread your protector you'll have a gauge to see when you are there. Casey
  5. U

    Gunsmithing Moly Resin - Advice Needed

    I do a lot of cerakote, Prep is everything. Spraying is not bad, just get a good HVLP gun if you plan on doing quite a few guns. If you have acess to a blaster use Aluminum oxide or garnet 100-120 grit. Make sure to degrease it well also. Good Luck :) Casey
  6. U

    Gunsmithing Badger ordinance brake

    The APA little bastard works well and you'll be very happy with it. I just put one on a light weight 300 ultra, its very nice to shoot now then before. Casey
  7. U

    Gunsmithing Remington 700 308W bolt with Surgeon 591 WSM action?

    Can you buy another bolt from surgeon? I asked at one time and they said I could buy another bolt for my 1086 action, but its been some time ago. Casey
  8. U

    Gunsmithing Barrel screwed on action at an angle

    I would take Jon up on his offer, he's a great guy and will get it straightened out for you. Did you get a chance to look at the threads on the action to see if they trued them? Casey
  9. U

    Gunsmithing Question on need for new bolt with a new barrel

    I always sell my old bolt when its new and buy a PTG one piece with all the bells and whistles that I like. Just up to you and how long you want to wait, I talked to them yesterday and they are 8-12 weeks on bolts depending on what you want. Casey
  10. U

    Gunsmithing Remington 700 LH action wrench

    Thanks guys, ordered a PTG wrench. Casey
  11. U

    Gunsmithing Remington 700 LH action wrench

    Im using the surgeon one now. I have only looked at the rear entrys on the net and wasn't sure how they worked. I haven't had a chance to handle one yet, love the help here. Thank you Bert, Casey
  12. U

    Gunsmithing Remington 700 LH action wrench

    I dont see many Left hand action wrenches to torque barrels on. What are you guys using that is a good solid LH wrench to torque on 80-100ft lbs Casey
  13. U

    Gunsmithing Cerakote: Blasting vs. Sanding

    Blast after you degrease and remove all oils and contaminates. If you don't your media will get contaminated and your coatings will be compromised and then your fucked, you'll be dumping all your media and cleaning your cabinet. I use CRC brake cleen, Chad uses methanol gas and has had great...
  14. U

    Gunsmithing Muzzle brake on small dia barrel

    Thanks guys :) Casey
  15. U

    Gunsmithing Cerakote: Blasting vs. Sanding

    Cerakote isnt hard to spray, it takes a little time to figure out your spray gun settings that work well for you. Once you have that and know what you can get away with you'll be good. Are you soaking it to remove the oils? I soak and heat to drive out any oils, thats a must also. I would blast...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts