• Winner! Quick Shot Challenge: Caption This Sniper Fail Meme

    View thread

Search results

Search the forum Search Articles
  1. T

    Is there a better way?

    <span style="text-decoration: underline"><span style="font-weight: bold">Background</span></span> I have a Compass Lake upper chambered with Frank's chamber. My load is 77 SMK, Lapua brass, Rem 7 1/2 primer, and 24grains Reloder 15. I full length resize the brass using a Redding S die that has...
  2. T

    using electronic powder dispensers? how accurate

    Re: using electronic powder dispensers? how accurate You bring up a good question. I use the Chargemaster and I have not taken the time to collect the data and calculate the upper and lower control limits, standard deviation etc. Anecdotally, I will state that the range is +/- 0.2 grains...
  3. T

    Do you F/L size new brass before loading???

    Re: Do you F/L size new brass before loading??? I don't for Lapua brass. But I do neck turn, chamfer, debur, uniform the primer pockets, and uniform the flash hole...
  4. T

    Ruger 10/22 Optics

    Purchased a Ruger 10/22 compact for my 11 year old daughter. Sending it to CPC for their full tune up. Considering a scope but need advice. Will be used mainly at the range out to 100 yards but might get the chance to take it out plinking in the Cascades. Appreciate your suggetions. p.s...
  5. T

    Which tumbler/media???

    Re: Which tumbler/media??? Berry's tumbler using the same fiddy/fiddy mix above. I throw in a dryer sheet that eliminates dust and half a cap of Nu Finish car wax. Cases come out very clean and shiney...
  6. T

    Gunsmithing PT&G Uni Throating Reamer

    Re: PT&G Uni Throating Reamer I had a custom reamer made by PT&G that is similar in many respects to the 95 Palma reamer. Since I am using up the 175 grain Matchking I needed just a little more throat, as the Palma reamer is set up for the 155 grain bullets. The extra throat allows 100%...
  7. T

    Redding Competition Neck Sizing Die Bushing Marks?

    Re: Redding Competition Neck Sizing Die Bushing Marks? My Lapua brass has never shown marks like that after neck sizing with Redding bushings (TiNi). On virgin cases I neck turn, trim/debur using the Giraud, and shoot. After firing I neck size, trim/debur using the Giraud, and shoot...
  8. T

    Neck sizing Lapua brass.

    Re: Neck sizing Lapua brass. Just short of the neck/shoulder junction has worked well for me...
  9. T

    Gunsmithing PT&G Uni Throating Reamer

    Re: PT&G Uni Throating Reamer No lathe required. A T-handle attaches to the reamer so you can turn it by hand. I was sceptical at first but after seeing the results I'm a believer...
  10. T

    Gunsmithing PT&G Uni Throating Reamer

    I had my Remington 700 cut with a 308 match reamer but needed a little more throat to accomodate the range of bullets I planned to use. By a little bit more I mean increasing the depth by 0.010. Purchased the subject throating reamer, followed the easy instructions, and successfully increased...
  11. T

    Firearms Academy of Seattle..

    Looking for a review of their Precision Rifle 1 and Precision Rifle 2 course. Considering attending next year and would appreciate your input. Thanks... http://www.firearmsacademy.com/overview.htm
  12. T

    Chargemaster Dispensing Question

    Re: Chargemaster Dispensing Question Don't know if that is an issue, as I always close the cover. When loading I set the chargemaster a tenth of a grain low of the target value and then double check each charge on an RCBS 505 before dropping it in the case. If the charge weighs two tenths...
  13. T

    Member Link Up SHWW Group

    Re: SHWW Group Sandrat - Kenmore range is 15 minutes South of Everett and features a 100 yard public range and a 300 yard member range. Machias is 20 minutes East of Everett where the public can shoot matches and Thursday practices at 500 yards (http://www.seattlerifle.org/)...
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts