Search results
-
ACIS / Timney trigger
I just put a Timney trigger on a Rem. 700 LA, the trigger feels great but is hitting somewhere in the stock. The stock is a ACIS and with the barreled action in I cannot move the safety. I'm just wondering if anyone else has had the same problem, and where I might have to inlet the stock. Any...- bob6117
- Thread
- Replies: 5
- Forum: Bolt Action Rifles
-
Gunsmithing Barrel nut
Does anyone know of an AR 15 barrel nut with a inside diameter of 1.050? I'm trying to replace the free float tube on my RRA Varmint with a quad rail. The Midwest Ind. handguard I was going to use requires a "standard" barrel nut wich will not clear the barrel diameter. Any help would be...- bob6117
- Thread
- Replies: 0
- Forum: The Armory
-
.223 - 5.56
Re: Loads for .223- 5.56 RRA A4 Varmint 20" Wilson 1/8 Wylde chamber Winchester brass Fed 205 pr 77 gr. SMK w/ cannetulure COAL 2.250 23.7 gr. RE-15 or Ramshot TAC 1/2" @ 100yd. 25 degrees F no chrono data yet, will update Bob- bob6117
- Post #113
- Forum: Reloading Depot
-
Rifle Scopes Super Sniper on AR- what mount?
Re: Super Sniper on AR- what mount? I'm thinking the Larue LT-104 might be a little high for a 42-44mm obj also. I going to order a Larue LT-158 same as the 104 except .080" lower, should have it at the end of the week. I'll post some pic's of it on my RRA Varmint w/ 10x42mm Falcon. Bob- bob6117
- Post #7
- Forum: Observation & Sighting Devices
-
any one use a fn a3g?
Re: any one use a fn a3g? I bought a FN A3G about 2 1/2 years ago. It never shot as good as I expected it to, so I sent it to GA Precision for a new barrel , pillar bedding, trigger adj. ect. It shot great when I got it back, but for the overall cost It would have been alot cheaper to go full...- bob6117
- Post #12
- Forum: Bolt Action Rifles
-
Rifle Scopes falcon 10x
Re: falcon 10x Shay, No the adjustments on the 10x are 1/4 moa only. Bob- bob6117
- Post #7
- Forum: Observation & Sighting Devices
-
Rifle Scopes falcon 10x
Re: falcon 10x Shay, They also make a mil-dot reticle. There is a picture of the reticle and a review on snipercentral.com Bob- bob6117
- Post #5
- Forum: Observation & Sighting Devices
-
Rifle Scopes falcon 10x
Re: falcon 10x Shay, They do make a fixed 10x. I have one on my AR, It has a reticle similar to that of a IOR MP8. 10 mils of holdover from center crosshair in half mil increments, and 5 mils windage holdover in half mil increments. Bob- bob6117
- Post #3
- Forum: Observation & Sighting Devices
-
Feedback Good Guy List
Re: Good Guy List JasonK DebosDave BobinNC Are all great to deal with. Thanks Bob- bob6117
- Post #7,461
- Forum: Buy - Sell - Trade
-
Feedback Good Guy List
Re: Good Guy List Austan and Strangedays are GTG. Fast payment and good comm.- bob6117
- Post #7,384
- Forum: Buy - Sell - Trade
-
Tungsten Disulfide (WS2)
Re: Tungsten Disulfide (WS2) Thanks for the information everyone. It sounds like HbN is the way to go, I appreciate the feedback. Bob- bob6117
- Post #8
- Forum: Reloading Depot
-
Tungsten Disulfide (WS2)
I did a search and did not come up with much. I am looking for an alternative to running moly in my 30-06. The purpose of this is to achive a higher round count before copper fouling becomes an issue. What I came up with so far with WS2 is as follows: 1. Cheap / easy application 2...- bob6117
- Thread
- disulfide tungsten ws2
- Replies: 7
- Forum: Reloading Depot
-
Loads for 30-06
Re: Loads for 30-06 190 SMK 61.0 gr RE-22 Win. brass Fed 210 2860 fps. 26.5" Rock barrel COAL 3.290- bob6117
- Post #12
- Forum: Reloading Depot
-
Range Report R&D Precision 30-06
I purchased a used R&D rifle from hide member Adam B a few months ago. Rem. 700 L/A Rock 26.5" fluted barrel w/ vias brake ACIS 1.5 Using Adam's reloading data: 190SMK 61gr. RE-22 Fed. 210 Win. brass I took the rifle out to 642yd. (longest range I have access to.) this afternoon. These are the...- bob6117
- Thread
- 3006 precision randd
- Replies: 11
- Forum: Ballistic Calculators & Field Results
-
Flat Top 223 load help!
Re: Flat Top 223 load help! 24.6 gr. of H 335 behind a 60gr. V-MAX worked well for me. Rifle was a RRA 16" 1/9 Vel. 2730-2750- bob6117
- Post #17
- Forum: Reloading Depot
-
Loads for 30-06
Re: Loads for 30-06 Lapua brass 175 SMK Federal 210M 48.5 gr. IMR 4895 COAL 3.300 I was using up some SMK 175's and IMR-4895 that I had left over from when I had a .308, and came across this load. I started out trying to duplicate 1968 LC Match (47.0gr. IMR-4895). Anyway, very accurate at...- bob6117
- Post #11
- Forum: Reloading Depot
-
Loads for 30-06
Re: Loads for 30-06 208 A-Max Lapua brass Federal 210M 57.0 gr. RE-22 26.5" Rock Creek barrel- bob6117
- Post #3
- Forum: Reloading Depot
-
Feedback Good Guy List
Re: Good Guy List MJW556 is gtg fast payment and good communication. Deal with confidence.- bob6117
- Post #6,701
- Forum: Buy - Sell - Trade
-
Brooks CZ trigger owners
Re: Brooks kit here and installed offroadr1 PM sent Bob- bob6117
- Post #18
- Forum: All Things Rimfire
-
Brooks CZ trigger owners
Re: Brooks kit here and installed Metalhead0483 The Brooks kit only consists of differnt weight springs and aluminum tubes to take up creep in the trigger. I already have mine set up, and am not using the lighter weight springs. I have 4 springs and 3 tubes. Your welcome to have them. If you...- bob6117
- Post #16
- Forum: All Things Rimfire
