Search results
-
Maggie’s THE "NOM NOM NOM" THREAD
Prime rib from last Christmas.- 300sniper
- Post #305
- Forum: The Bear Pit
-
-
-
Gunsmithing New house, new garage. . .
I've had good luck with the Home Depot Rustolieum garage floor epoxy when applied properly. After years of dragging steel across it while fabricating and a ton of floor jack use, it does show wear but for home use, I think it's a good option. If money is no object, I'm sure there's better...- 300sniper
- Post #10
- Forum: The Armory
-
Gunsmithing "clocking" a barrel while chambering.
On an off the shelf barrel, there's no way to do so other than luck of the draw. We all know savage barrels can't shoot good because of the importance of muzzle timing/chamber indicating method....- 300sniper
- Post #14
- Forum: The Armory
-
Gunsmithing "viper" chambering fixture slippage.
Exactly what I was going to say. On a manual machine barrel work speeds, probably not much of an issue with less than 20" of unsupported barrel. I wouldn't be doing it with my G50 clamped at 5k.- 300sniper
- Post #5
- Forum: The Armory
-
Gunsmithing 300 Norma question
25+ MPG on the highway isn't too bad for a large displacement V8 performance car....- 300sniper
- Post #4
- Forum: The Armory
-
Gunsmithing "clocking" a barrel while chambering.
Who says once you pull you long, (relatively) flimsy barrel out of you dual spider chucks and screw it onto a receiver so all the weight is hanging from one end, everything is in the same place it was on the machine?- 300sniper
- Post #8
- Forum: The Armory
-
Gunsmithing Throating Reamers
I think you'd have to try hard to get a throating reamer to cut off center. Actually, I'm not sure you could if you tried. I agree, having a single form tool is the way to go as you can tell the customer exactly what they have, and be able to back it up, but I don't see lengthing the throat of a...- 300sniper
- Post #11
- Forum: The Armory
-
-
Gunsmithing Recent Build
Selective photography! Notice my work benches or floor weren't in the pictures! It's actually pretty nice but still a work in progress. Once I get all the clutter put away, I'll mop the floor and post some shop pictures.- 300sniper
- Post #5
- Forum: The Armory
-
Gunsmithing Recent Build
Owner is loading for it tonight. Should get some feedback in the morning.- 300sniper
- Post #4
- Forum: The Armory
-
Gunsmithing Recent Build
A recent build with some nice components. Defiance Deviant Hunter long action KMW carbon fiber Sentinel stock Proof Research carbon fiber barrel It was chambered in 300 Win Mag.- 300sniper
- Thread
- Replies: 4
- Forum: The Armory
-
Gunsmithing Productive Sunday.
I find running it dry and fast on the hammer setting works best. The chips come out blue hot so I know the heat is not going into the barrel or tool.- 300sniper
- Post #9
- Forum: The Armory
-
Gunsmithing Productive Sunday.
I have adjusted them for minimal endplay and have verified acceptable TIR at the chuck. It's good to go!- 300sniper
- Post #6
- Forum: The Armory
-
-
Gunsmithing Nightmare gunsmith Northwest Precision Rifles * REFUND RECEIVED
Not sure exactly what tooling you are using, but I never mark up properly applied finishes, nor impact a recoil lug while removing/installing a barrel.- 300sniper
- Post #64
- Forum: The Armory
-
-
Gunsmithing High Tech Solution To Low Tech Problem
...or just messing around https://www.facebook.com/permalink.p...72791756090183- 300sniper
- Thread
- Replies: 1
- Forum: The Armory
-
Gunsmithing Lathe RPM for threading?
For most people posting on this page, threading RPM is going to have far more to do with reaction time and comfort level than optimum SFM.- 300sniper
- Post #16
- Forum: The Armory
