Search results
-
E
MDT Oryx Chassis
Just installed by Tikka T1x into the Oryx chassis. Just quick trip to the range, shoots great despite the windy conditions. Definitely likes the Action screws torqued pretty tight. Just over an 1 inch at 100m with CCI SV. Shoots SK Rifle Match well also. I installed a generic 12 inch Arca...- ed99
- Post #376
- Forum: The Armory
-
E
Rubber type spray for shooting bag
I've been using plasti dip also, holding up pretty good! Ed- ed99
- Post #6
- Forum: The Armory
-
E
Which bipod for arca swiss rail?
I'm running a Ckye Pod and I really like it for rimfire PRS on my Oryx chassis running an Arca rail. Lots of adjustment and works well off of the different shooting positions. Very stable as well. I've run the Atlas and Harris bipods, but I prefer the Ckye Pod. ? Ed- ed99
- Post #13
- Forum: The Armory
-
E
MDT Oryx Chassis
I switched to slightly shorter Arca rail and I drilled and tapped the end for a 10/32 thread and installed a sling stud. Ed- ed99
- Post #353
- Forum: The Armory
-
E
MDT Oryx Chassis
I've been getting some good groups at long range with my Vudoo and my Oryx chassis. The Oryx chassis provides a good solid platform which helps getting those long range hits. This is a typical group with Center X at 200 m (218 yards ) when the wind isn't blowing too hard ☺ Ed- ed99
- Post #313
- Forum: The Armory
-
E
DeLane Development Group Rimfire Ventures
I have been shooting my Vudoo for a couple months now. Using an Oryx chassis, Triggertech Diamond and Athlon Ares ETR. Really like the set up. I've been shooting a little bit of long range and have had some good results with Center X and a sub moa group at 218 yards with Fed HV Match (fluke...- ed99
- Post #2,577
- Forum: All Things Rimfire
-
E
MDT Oryx Chassis
Here u go??? Running an Athlon Ares ETR on a Vudoo V22..- ed99
- Post #302
- Forum: The Armory
-
E
SK Standard Plus Change?
I've found the same thing with SK+ and different lots from several yrs ago. Now that I started to chrono it over a LabRadar I have found wide variations in velocity. Some lots are 1050, 1070, some are down to 975 with poor accuracy. One of my screamer groups shot in my Vudoo was .55moa with...- ed99
- Post #7
- Forum: All Things Rimfire
-
E
Tikka T1X
I just got my Oryx chassis and I ordered the spacer kit, it had 4 of the (1/4 in) spacers in the kit . I checked the website and you get 1 inch total for $20. ;) I'm really liking the chassis and I'm going to get one my T1x that is on order..- ed99
- Post #875
- Forum: All Things Rimfire
-
E
MDT Oryx Chassis
My Oryx chassis showed up and I dropped in my Vudoo V22 to try it out. Took all of about 1 minute to install. I installed an Arca rail on the bottom, a direct mount for my tripod. I ran out of M Lok bolts so I used 1/4 in stainless bolt with a nylock nut. The nut fits inside the forend...- ed99
- Post #251
- Forum: The Armory
-
E
Tikka T3X A1 TAC concern?
If you loosen the two bolts on the handguard where it meets the receiver, you can rotate the handguard slightly..... Ed- ed99
- Post #4
- Forum: Bolt Action Rifles
-
E
PRST - mod (now with pics)
I've been running my PRST (carbon fiber tripod) for over a year. I started out with a Sirui K-30x Ball Head (66 lb load capacity) and a Hog Saddle. It had a bit to much flex for my liking as the ball head raised the Hog Saddle from the tripod legs. I dumped the ball head and direct mounted...- ed99
- Thread
- Replies: 1
- Forum: The Armory
-
E
Leofoto tripods
Would the Manfrotto 100 mm half ball leveler work with LN404c? Their half ball seems to be reasonably priced at around $51 https://www.bhphotovideo.com/c/product/366661-REG/Manfrotto_500BALLSH_500BALLSH_High_Hat_Adapter.html- ed99
- Post #92
- Forum: The Armory
-
E
Rifle Scopes Easy scope leveling fix
I agree they're great! I use mine with a carpenter's vice to hold the rifle. I get the rifle level and then I mount the scope and use a string and plumb bob hanging off a 6 ft step ladder 25 m away Ed- ed99
- Post #2
- Forum: Observation & Sighting Devices
