Search results

Search the forum Search Articles
  1. R

    watch suggestions

    Re: luminox watches? I have had 2 luminox f 117 nighthawk watches. The first one lost a tritium crystal after 3 months. They replaced it no problem (Not salztmans the old repair center). Second has had lots of daily wear but no problems for 3 years then the unidirectional bezel retaining...
  2. R

    Inexpensive but sturdy rifle shipping container?

    Re: Inexpensive but sturdily rifle shipping container? I agree with MWDG3 Order from someone online that way you get the shipping box to put it back in. I ask for them at walmart and they said they are shipped to them in bulk with no box. I have also done what Tbag said break the rifle...
  3. R

    Best laser rangrefinder

    Re: Best laser rangrefinder I agree with Chiller I have the swarovski you can get them here used for 750 to 800. I think there is one "NEW" for 850 in the optics section. The only 2 things I don't like about it is the circle reticle is to big should have a dot in the middle. 2 I had to make...
  4. R

    Gunsmithing Removing Noveske pinned brake

    I want to remove my noveske factory brake and replace my handguards with a rail. The pin is obvious on the underside of the brake about 3/16 kind of large compared to other pinned brakes I have removed (and replaced). Has anyone removed one of these and salvaged it to put it back on? Is the...
  5. R

    Gunsmithing timing PRI Brake on ar barrel.

    Re: timing PRI Brake on ar barrel. Thanks CS. I really felt I was having to apply to much torque for my comfort so I went the grinding route. Timed up fine. I looked at the washer an it appearred to have pleanty of "crush" room. Not sure why it was so difficult to torque. Anyway I had...
  6. R

    Gunsmithing timing PRI Brake on ar barrel.

    I have a Ar with a PRI MB on it It has been in the safe for a while. This is one of the few I bought assembled from MSTN if I recall. Just took it out and noticed the brake is 180 out of time. Took it off checked to make sure it was a crush washer and went to retighten it. It is way to tight...
  7. R

    Gunsmithing Notching feed ramp for alpha mags.

    Re: Notching feed ramp for alpha mags. Thanks Treebasher thats a big NO then. I really dont see how milling the mag front would stop the bullet tip from hanging up under the feed ramp. Which is what I perceive is the problem. Maybe I just haven't thought about it enough. Thansk again Rad
  8. R

    Gunsmithing Notching feed ramp for alpha mags.

    I was thinking on changing my Manners stock with seekins bottom metal to Terry cross sentinel. However I want to keep my OAL were it is in the seekins mags. I ask about moding my tac 30 for the Alpha mags and Jerry said it would void my warranty. I understand his position but was curious if...
  9. R

    Rifle Scopes Vortex 4-16x50 MRAD ffp PST Scope Report

    Re: Vortex 4-16x50 MRAD ffp Scope Report This is why I love this forum. People who use the stuff take the time to tell you the honest truth. Thanks for the review. I have been on the fence about a PST but right after I read this I saw Webyshop.coms add showing the 4-16 in stock and ordered...
  10. R

    Rifle Scopes case for swarovski LRF

    Re: case for swarovski LRF Well The tongue thing and the caffeine break didn't help (or it may have been a beer or 12) but my line sucked so against better advise I took it to the belt sander. As expected I did get pilling and roles but I did get a flat straight line all the way around...
  11. R

    Rifle Scopes case for swarovski LRF

    Re: case for swarovski LRF I guess I need to lay off the coffee and get my tongue just right then. I have a bunch of number 10s and 11 blades laying around and just got my covers in friday (ain't Brownells wonderful). Hopefully I can get to it today. thanks for all the help Rad
  12. R

    Rifle Scopes case for swarovski LRF

    Re: case for swarovski LRF How do you think a belt sander would work? Just not that good with a blade. Thought if you watched the heat cut close to the line and finished with a belt sander might get a good clean line? Any thoughts?
  13. R

    Rifle Scopes case for swarovski LRF

    Re: case for swarovski LRF Thanks Aries ordered the tac ready last night looks like I need 3 #19s. Great post.
  14. R

    Rifle Scopes case for swarovski LRF

    Anyone know of a case or lens covers for a 8x30 swarovski LRF. Looked at BH and opticsplanet. All I see is the plastic "Holster" I was wanting something to protect the objective lenses and the body better. AHA Rad
  15. R

    alpha mags in tac 30 and pierce actions

    Re: alpha mags in tac 30 and pierce actions What are you guys making the mod with? I have read people using a dremel, man that concerns me. I have found very few things I can't screw up with a dremel:) Dustin what did you use? Do you put on angle on it like a M4 feed ramp or just make it...
  16. R

    338 neck tension

    Re: 338 neck tension Thanks. Sounds like my 365 is right in line. Rad
  17. R

    338 neck tension

    I just reloaded my first loads for my lapua. the only bushing I had was a 364 and 365. lapua brass measured .015 plus 338 equals 368 I thought 366 would be perfect but was 2 inpatient to wait for the bushing. Anyway loaded 300 grain sierras withthe 365. Handle pressure felt a little tight on...
  18. R

    alpha mags in tac 30 and pierce actions

    Re: alpha mags in tac 30 and pierce actions Thanks Ace I will try that tomorrow. Rad
  19. R

    Rifle Scopes Any skinny,feedback on new March scope?

    Re: Any skinny,feedback on new March scope? My major concern is there ability to support their stuff. Everything looks great the reports on them are phenomenal but try to get one. I ain't the smartest guy around but I was all over their website and just not real intuitive. dtac where did...
  20. R

    alpha mags in tac 30 and pierce actions

    Will Alpha type 2 308 mags run in a stiller tac 30 without modifying the feed ramp. The rifle has a seekins mag system @ 2.940 OAL in it now so it seems it should fit. I am thinking of changing the stock to a Mcree and want to keep the extra length. Is there a opening length to use as a guide...
Top Bottom
Back
Home
Forums
Merch
Alerts