Search results

Search the forum Search Articles
  1. LANCER

    Gunsmithing Carbon ring.

    Can someone post a picture of what a true carbon ring looks like? I haven't checked the bore (I have a teslong also) but my Barrett MRAD 338LM has been giving me hard bolt lift regardless of pressure or load. I'm down 4 grains from previous known good load and I get bolt lift (hard bolt lift...
  2. LANCER

    Gunsmithing Proof CF prefit barrel on Tikka T3x - Bolt Closes on no-go gauge but not on Field gauge

    Thanks guys. I'll get a new batch of Lapua or Peterson for it.
  3. LANCER

    Gunsmithing Do Tikka firing pins need to be bushed for SR primers?

    Nope. All good.
  4. LANCER

    Reloading Equipment WTB .338 Lapua Brass

    I've got about 400 pcs of once fired Prime Ammo (Norma/RUAG) that is fully processed (resized, trimmed, annealed) I could let go if you don't find what you're looking for.
  5. LANCER

    HELP!!! Trying to find a matching a Cerakote color

    I've been trying to replicate this myself. (resurrecting an old thread, I know) but the closest I could find so far is Federal Standard Field Drab. It's not exact, but also close and has a slight green tint. I would have expected Coyote to be close, but it's actually way too light almost like...
  6. LANCER

    Gunsmithing Proof CF prefit barrel on Tikka T3x - Bolt Closes on no-go gauge but not on Field gauge

    So I decided to install a Proof Carbon barrel on my T3x. Prior to install, I cerakoted both the action and the steel parts of the barrel. I did not tape off the action face nor the mating face of the extension, although I DID tape off the barrel threads. When I installed, I only had a...
  7. LANCER

    Amp annealer question

    Same measured mass at the necks apparently. I've gotten similar results. My Lapua 338LM I think got 165 because I turned the necks.
  8. LANCER

    .338 LM / US869 / 285 AMAX

    Negative. In all the years since 2014 when I started reloading for 338LM, I never once was able to buy RL33.
  9. LANCER

    Euro presses: Talon vs. Turban vs. Lenzi

    Might look at the Area 419 Zero turret press. Made in the USA and will have a second batch of them produced soon. (first batch sold out quick)
  10. LANCER

    Euro presses: Talon vs. Turban vs. Lenzi

    I don't have anything to add other than I really lust after a Turban 140mm.......I think it's all in the kinematics....linear bearings, finely machined surfaces, tight tolerances. Will probably do nothing to increase precision (or that 99% of shooters cannot outshoot what a Rockchucker or...
  11. LANCER

    .338 LM / US869 / 285 AMAX

    I almost forgot, you can try IMR 7828 as well. It burns super clean. I have the SSC (super short cut) variant and leaves a lot of space in the case. I would go with the standard 7828 if you can find it.
  12. LANCER

    .338 LM / US869 / 285 AMAX

    Mine does pretty well with 300 gr. Scenars. Between 105-106 grns of US869 works well for me but it's not temperature stable, was getting ridiculous velocities and some mild pressure signs this summer at 102-104 degrees. You can work up some great loads with it. It's a bit of a hidden gem...
  13. LANCER

    Music to reload by

    Nothing. I like to focus on what I'm doing without distractions. I'm strange like that though.
  14. LANCER

    Reloading Equipment SOLD Qty 1000 Berger 30 cal 155.5 Fullbore bullets $400 shipped CONUS+AK

    OK I'll take 1000. Send me your paypal info pls.
  15. LANCER

    Reloading Equipment WTB or WTT for Berger 140 Grain 6.5 VLD Target Bullets

    I have at least 1 box of 100 of 26401. Might have 2 but not sure if my second box is partial or not. Whatcha got for trade? I don't need to sell, but if you really need them, make me an offer. I'll update total quantity in a couple hours.
  16. LANCER

    Knights Armament

    The receiver forgings and BCG (at least the pre-ambi ones) were made by LMT for KAC according to a lot of people that know better than I. I can't afford KAC so I go with LMT.
  17. LANCER

    Reloading Equipment WTB - Barrett MRAD Bag Rider

    Looking for a Barrett MRAD rear bag rider for the pic mount. Barrett's site has been out of stock for a while. Need one soon. Thanks
  18. LANCER

    Reloading Equipment SOLD V3 package. FX120/ Autothrow/ AutoTrickler 1000 shipped

    Someone stole this. Good find.
  19. LANCER

    Reloading Equipment WTS: Reloading Equipment/Supplies

    I'll take the 140 Berger Hybrid x 500 box
  20. LANCER

    Reloading Equipment ***SOLD*** WTS: Giraud Annealer Dual-Flame unit and/or with Annie Induction conversion

    Here we go: Annie induction annealer kit complete with following parts: Induction power supply 1200W Water recirculating cooler (with both power options: wall wart or directly off the Annie connector) Water cooled induction work coil (.587 opening for anything up to .308 body diameter) Water...
Top Bottom
Back
Home
Forums
Merch
Alerts