Search results

  1. RADcustom

    Gunsmithing Firing pin bushing

    Gre'-Tan Rifles http://www.straightshotgunsmithing.com/page1
  2. RADcustom

    Sidearms & Scatterguns Top Pistolsmiths List attempt

    They are referring 1911 work to his nephew @ Hayes Custom Guns. https://www.facebook.com/HayesCustomGuns?fref=ts
  3. RADcustom

    Gunsmithing Thin barrel threading... possible?

    The first 308 barrels from dpms were threaded 1/2x28 and had no issues.
  4. RADcustom

    McMillan stock - brittle gelcoat layer?

    I would mix some epoxy and try to work it in the hole with a small wire prior to fixing the chip.
  5. RADcustom

    Looking for a smaller 4x4 truck, need advice

    I have had several Toyota 4x4's and loved them. It would have to be an outstanding deal for me to own anything else besides a Toyota for that type of truck.
  6. RADcustom

    who can answer this? Primers

    I'm betting it's something else. You didn't mention what brand of primer you were using but, you might try a different one. How confident are you that your chronograph was giving good information? Primers seated a little deep may cause some odd signs like premature flattening or cratering but...
  7. RADcustom

    Imr-8028 xbr?

    I think it is actually 8208. Yes, it works great in 308.
  8. RADcustom

    Hunting & Fishing Largest animal killed with a 22lr

    There was a 50# Chow that no longer comes around the farm anymore because he ran into a CCI minimag, DRT.
  9. RADcustom

    Rifle Scopes 20 MOA Scope Base Prices

    The easy answer is, it depends. I have used both and they both do the job but, if it is something I am going to need to depend on, I try to get the best quality I can afford. I would expect the specs for the more expensive bases to be better which would in turn make for better fitting rings.
  10. RADcustom

    Gunsmithing Input on what happened to this brass...

    The best way to prove it wasn't the ammo is to fire one of the reloads in your new rifle. If it survives, then you can tell everyone in this thread to kiss your a$$. Be sure post video.
  11. RADcustom

    latest

    Very nice. Is this a personal rifle or one you built for someone? Are you escaping from CA or relocating in state?
  12. RADcustom

    HOLE IN HOLE show them!!

    AIAX 260 @ 330yrds AIAX 260 @ 415yrds Badger 2008 6.5x47L @ 900yrds
  13. RADcustom

    Gunsmithing Wasnt going to do the oversized recoil lug thing......

    That only makes sense if you do your own work on a manual machine. ;)
  14. RADcustom

    Gunsmithing Is this the correct Devcon for action bedding?

    It doesn't come in tubes because it is a putty. 10110 is not a 1:1 mix ratio so there is less chance for shrinkage. Get the 1lb jar. It is very handy and lasts a long time.
  15. RADcustom

    Gunsmithing Opening up a Remington 700 bolt face?

    The bolt face is easy to do but, you will need to install a different extractor
  16. RADcustom

    10/22 expectations

    There are a lot of variables to your question. Given a quality barrel with a match chamber and good ammo, I have seen 1/4 inch groups at 50yrds.
  17. RADcustom

    Gunsmithing Want UNKNOWN 1911 smith!!!!!!!!!!!!

    https://www.facebook.com/HayesCustomGuns They are just getting things off the ground on their own but, they are the grandsons of Jim Clark Sr. They can do whatever you want.
  18. RADcustom

    Gunsmithing Barrel blank?

    It is most likely an index mark for the rifleing machine.
  19. RADcustom

    Where is jason k ??

    That's probably why Lowlight had so much trouble with the transition. :D
  20. RADcustom

    scope mounting on a rem 700.....

    Get some rings and be happy. You will have more versatility.