Search results

Search the forum Search Articles
  1. -Time-

    Sub Moa 16" barrel under $250?

    Larue stealth barrels. $225 and the one on my spr shoots lights out. I don’t typically shoot for groups, but the last time I did it was a ~0.247” 5 shot group at 100 yards.
  2. -Time-

    Rifle Scopes NIGHTFORCE NX8 1-8X24 F1 ?

    My dads got one. I think most of the comments here really cover it. Compared to the ATACR, the NX8 gives you a much smaller footprint, at the cost of a tighter eye box. You do see a little bit of dimming going to 8x too, but that’s the nature of a 24mm objective. Maybe on a close to medium range...
  3. -Time-

    Rifle Scopes Tangent Theta tool less zero question

    Interesting. My 525P is .5 below. To answer your 2nd question though, yup. If your zero for another barrel is -0.5mils, simply dial -0.5, loosen the turret, lift and turn to zero, then tighten the turret back.
  4. -Time-

    Help me find an AR10 receiver set

    I didn’t think about finishing an 80%! Thanks for the resources. I’m kinda OCD about weighing rifle parts, but I never thought to put them in a spreadsheet. Smart!
  5. -Time-

    Help me find an AR10 receiver set

    Clean looking gun! I forgot about the pdq, I’ll keep them mind thanks!
  6. -Time-

    Help me find an AR10 receiver set

    Thanks for letting us know about this! I really love all the features of the Zev, I’m just not huge on the aesthetics, but for sub $500 they might win out. I’d like to contact Zev to see if they’d run off a more plain receiver set with their features, or Todd at SLR to see if he’d be willing to...
  7. -Time-

    Help me find an AR10 receiver set

    Damn, I’ll definitely keep an eye out then, thanks!
  8. -Time-

    Help me find an AR10 receiver set

    I like the lmt lower, but damn that upper hurts at $3500, and I can’t find ECC uppers anywhere.
  9. -Time-

    Help me find an AR10 receiver set

    That’s how things usually go for me LOL. If the ECC had the bolt release I’d think about it, but afaik its new to the ACC gen rifles, so I’d have to buy an ACC and then buy a urx 3.1 and have the hand guards swapped.
  10. -Time-

    Help me find an AR10 receiver set

    I’ll give them a call tomorrow thanks!
  11. -Time-

    Help me find an AR10 receiver set

    Does mega exist anymore? I thought they got absorbed by Zev?
  12. -Time-

    Help me find an AR10 receiver set

    I’m slowly planning out my next AR10 build. It’ll be a 16” .308, fairly light weight, and a urx 3.1 to match my small frame SBR and SPR. The problem comes finding a receiver set. I want something MK11/SR25 style. Slant cut in the rear, simple styling, but I also want the right side bolt release...
  13. -Time-

    Fixing to get a new barrel for my 6.5cm

    The heat mitigation and weight seems to be the real benefits of the proof barrels. Taking all the weight out of the front of the gun makes it very enjoyable to carry (although there is an argument to make about ease of shooting a rifle with more weight at the front) And the heat mitigation is...
  14. -Time-

    Diagnose my heavy bolt lift

    I bit the bullet on a Lyman borescope, so we’ll know for sure soon. Anyone tried cutting brass just below max to eliminate carbon ring build up, or is it in vain?
  15. -Time-

    Diagnose my heavy bolt lift

    About 350 on the barrel. Rounds close easy and the ejector is clean. Bullets will slide freely into fired cases, I think earlier ones didn’t slide freely because they got dinged up, I made sure to catch all of this brass. You’re right the brass OAL isn’t moving much at all, maybe...
  16. -Time-

    Diagnose my heavy bolt lift

    Well I chrono’d the loads today. They’re running ~2866, about 70fps faster than it used to be. I didn’t get a really heavy bolt lift, but ejector marks were still present on most of the brass. I cleaned the chamber, to no effect. I’m truly at a loss for why this load shoots 70fps faster when in...
  17. -Time-

    Diagnose my heavy bolt lift

    Yes, and I tried bumping the brass from the batch that were over pressure. the over pressure rounds are harder to chamber than the non, even after bumping. It seems to be around the belt, but unfortunately the Larry Willis collet die I have doesn’t work with my forester coax.
  18. -Time-

    Diagnose my heavy bolt lift

    I went round by round and made sure every case was sized, and all of the lube was wiped off. RCBS chargemaster is throwing accurately as well. I’m taking it out Saturday, and I’m going to bring cleaning stuff, but I want to drop a couple rounds before cleaning, to cross off variables for the...
  19. -Time-

    Diagnose my heavy bolt lift

    My thought was not that the case was getting bumped too much, but rather just enough for me to not notice it was right when loading, and the inability for the brass to expand much was increasing pressures, but maybe I’m incorrect about that. I have noticed the home brew case lube is very finicky...
  20. -Time-

    Diagnose my heavy bolt lift

    Duely noted about measuring neck ID. These next cases are 2.605 before sizing so I should be good on OAL. What do you recommend to clean the neck/chamber area? I’m struggling to even find a 300wm chamber brush.
Top Bottom
Back
Home
Forums
Merch
Alerts