Search results

Search the forum Search Articles
  1. B

    You know you're shooting long range when:

    Re: You know you're shooting long range when: when you drive to the highest altitude you can reasonably find and then shoot from the roof/bed for extra altitude.
  2. B

    Take off barrels

    Re: Take off barrels Factory barrels generally contain stress due to the way they're manufactured (cheap) so expect POI to shift if it gets really hot (rapid firing). Run Tubbs Final Finish bullets through the factory barrel and then just shoot the hell out of it with minimal cleaning...
  3. B

    Rifle Scopes Remington 700 bolt will not come out.

    Re: Remington 700 bolt will not come out. http://www.urban-armory.com/cart/blueprints/reming_700.gif #4 shows the bolt stop that is inside the receiver.
  4. B

    Rifle Scopes Nightforce blurry

    Re: Nightforce blurry OP - do you wear eyeglasses by any chance? I found that even if everything is adjusted right, shifting your eyeglasses (e.g. up or down your nose) affects clarity.
  5. B

    Gunsmithing 308 Reamers

    Re: 308 Reamers do you guys own a lathe or is it possible to ream without a lathe? Thanks. Just wondering if its wor getting a good reamer if I dont own a lathe.
  6. B

    Tula primers for .308 ??

    Re: Tula primers for .308 ?? Tula is great when the brass primer cup is loosening up, like you said its a bit thicker than CCI, Rem 9 1/2, and 210. They're consistant and I haven't had a misfire yet after 2500 reloads.
  7. B

    Bad Winchester Brass

    Re: Bad Winchester Brass Honestly, in the long run Lapua is cheaper. nuff said.
  8. B

    any one ever use these bullets

    Re: any one ever use these bullets IMO the projectiles on gunbroker are good to go, like what others are saying - slight to little difference in accuracy compared to beand new but at a fraction of the cost. With respect to the above Widener's bullets, those aren't M118LR rounds nor are they...
  9. B

    Safety issue with dented 175gr M118 tips

    Re: Safety issue with dented 175gr M118 tips Anyone have experience with these & whether accuracy is affected by pulldown marks compared to new 175 gr SMK's?
  10. B

    Hunting & Fishing best coyote bait to hunt over?

    Re: best coyote bait to hunt over? Sorry if this sounds dumb but I've never even seen a coyote in person before - what do you guys do with coyotes? Sell the pelt? how much do they go for? What about the meat?
  11. B

    1000 yard hits

    Re: 1000 yard hits Just so I understand, I read somewhere that the bullet initially flies in a corkscrew pattern (like a soap suds spiraling down a drain) for the first few hundred yards or so. So this notion of "falling asleep" basically refers to the point where the bullet loses just enough...
  12. B

    Rifle Scopes torquing ring screws

    Re: torquing ring screws Hey blackump, I tighten them down to 15 lbs for rings & scope. 65 lbs for rings to base
  13. B

    Anybody Using New 308 Nosler Brass

    Re: Anybody Using New 308 Nosler Brass do a real search: http://www.google.com/cse/home?cx=010955838166721108978%3Aqcbx5qqy10o&hl=en
  14. B

    AICS AX?

    Re: AICS AX? looks like the tac mod chassis http://tacmodstock.com/
  15. B

    1000 yard hits

    Re: 1000 yard hits The way I see it its comparing apples to oranges. Sniperaviator says: math for 1 moa rifle shows on average it should group roughly 14.1 inches at 1000 yards. Tom Sarver says: my .2 moa rifle groups consistently tighter at 1000 yards than 100 yards. If this were a...
  16. B

    size fresh lapua brass????

    Re: size fresh lapua brass???? just neck size after firing. Read the stickies as they pretty much answer your questions and any more you may have.
  17. B

    Advanced Marksmanship Cheek Weld with Bell and Carlson

    Re: Cheek Weld with Bell and Carlson I had the same problem which is why I went with a Bell and Carlson A2 (no cheekpiece) and got a Karsten cheek rest. The benefit with Karsten is that its kydex plastic so you can mold it to your cheek with just a small heat torch. Apply the heat. torch to...
  18. B

    DAMN YOU REMINGTON, and your innacurate rifles

    Re: DAMN YOU REMINGTON, and your innacurate rifles Also, other than accurqcy, the finish was pretty crappy. I had to sand down the bolt body, feed lips, magazine edge to stop it from scratching up my brass. I also had to dremel the bolt lift arrea to smoothen it out. Overall the action was...
  19. B

    DAMN YOU REMINGTON, and your innacurate rifles

    Re: DAMN YOU REMINGTON, and your innacurate rifles Wait till you swap for a quality stock with proper bedding, lap the lugs, quality scope base and rings (I lapped my scope rings) then you really have a shooter. My SPS-T currently shoots .35 moa with handloads (shots done at benchrest) and...
  20. B

    Military Pull down 175 grain Match bullets

    Re: Military Pull down 175 grain Match bullets I just got some pulled m118lr projectiles which are 175 grain SMks. They have slight pull marks and light scratches. Will load up a few and shoot them over the weekend. They're coated with something sticky (grease?) anyone got ideas to get it...
Top Bottom
Back
Home
Forums
Merch
Alerts