Search results

Search the forum Search Articles
  1. T

    SR-25 type magazine options

    Re: SR-25 type magazine options If you buy the ASC mags you will have warranty if something should not work. The guys at ASC are quality minded.
  2. T

    Gunsmithing Kings Armory

    Re: Kings Armory Richard W King The Kings Armory 3005 Monties Ln Arlington, TX 76015 (817) 265-0118 (Phone)
  3. T

    Gunsmithing OSPREY PISTON ISSUE

    Re: OSPREY PISTON ISSUE If the case is just barely ejecting it is not making a full cycle. What Stock ,Spring and Buffer are you using. The Osprey's I have installed liked a standard carbine spring and buffer would not run well with an "H" buffer. Confirming this is New ammo being testes...
  4. T

    Gunsmithing OSPREY PISTON ISSUE

    Re: OSPREY PISTON ISSUE Have the gas rings been removed from the bolt?
  5. T

    Gunsmithing New parts washer, Need solvent advice

    Re: New parts washer, Need solvent advice I use Mineral Spirits and Marvel Mystery Oil this combination has worked well for me for over 30 years. Ratio of one gallon Mineral Spirits to one quart of Marvel Mystery Oil.
  6. T

    SMK's for deer hunting?

    Re: SMK's for deer hunting? SMK's worked well for me I tend to shoot the hogs in the ear as the dont go running far after the ear shot! They work well on Deer' Elk and Moose just fine as long as you do your job.
  7. T

    Gunsmithing Anyone know a good gunsmith in socal?

    Re: Anyone know a good gunsmith in socal? Send it to Ammo Bros in Ontario
  8. T

    1426 yard deer

    Re: 1426 yard deer Dustin I know I'm competent enough to hit a 20x20" steel at 1000 meters with my .308, its not even hard. But that doesn't mean I think its appropriate to even try at deers on 500 meters just because "I can". Deers can make a sudden move, meaning I'm ending up in the...
  9. T

    Some Mosin Nagant Humor

    Re: Some Mosin Nagant Humor I had a customer bring me 2 of them to cut the barrels and Target crown to 26 in turn down the bolts install Monte Carlo ATI stocks and scope,rings and bases. They called to see if the job was done I replied Yes! He enthusiastically hollers out to his brother...
  10. T

    Gunsmithing AR flash hider removal

    Re: AR flash hider removal It may not have been loctite. The flash hider may have been blind pinned and welded.
  11. T

    Gunsmithing best method for cleaning ceramic stones

    Re: best method for cleaning ceramic stones Normally use mineral spirits or ultra-sonic cleaner.
  12. T

    Gunsmithing McRee Precision

    Re: McRee Precision? Best stock/chassis out there in my opinion. I own 4 of them less recoil and accuracy gains on 2 of the rifles @ 1 in and better @ 600 yds and beyond.
  13. T

    Gunsmithing AR-15 burst firing? Need Advice!

    Re: AR-15 burst firing? Need Advice! I am also Colt certified. Sounds like you have springs mixed up or installed incorrectly and or missing. Depending on the LPK you have some are Chinese junk! with parts that are even close to spec. 1)Under the disconnector there is a somewhat conical...
  14. T

    Gunsmithing KABOOM Today...with damage, please help.

    Re: KABOOM Today...with damage, please help. Since it is a Model one I would forward the upper to a AR Smith. I have never seen a model one that is really 5.56. So the I figure the 6.5 to do the same They cut the barrel chamber short. I have seen these results many times from model one...
  15. T

    Gift for the father in law.

    Re: Gift for the father in law.
  16. T

    Range Report Did this bullet come apart in the air?

    Re: Did this bullet come apart in the air? Barrel being melonited was not the problem here a twisted barrel was.
  17. T

    Range Report Did this bullet come apart in the air?

    Re: Did this bullet come apart in the air? Another thing to check. I have a customer bring me a barrel that he had a brake installed somewhere it too was melonited and sending bullets everywhere. What I found was the brake was overtightened as it was being timed and twisted the threaded...
  18. T

    Gunsmithing Taurus M44 44mag factory load

    Re: Taurus M44 44mag factory load The 305 and 320 Corbon's will shake it loose and void warranty I have see this twice in the shop. Stay with the 240 gr and the light 255 you will be fine.
  19. T

    Gunsmithing Gunsmithing Question

    Re: Gunsmithing Question Try cleaning the Chamber and Barrel may have some residual Blasting grit/media in there.
  20. T

    Gunsmithing Why not Gunsmithing for a living??

    Re: Why not Gunsmithing for a living?? Well said Chad!!
Top Bottom
Back
Home
Forums
Merch
Alerts