Search results

Search the forum Search Articles
  1. S

    Accuracy International Picture Thread

    @Sixfivesavage it’s 24”, and it balances about the same as my 16” .308 barrel. It’s slightly rear heavy if you balance it right in front of the magazine.
  2. S

    WTS- Spuhr A-0011 and A-0015

    Up
  3. S

    Accuracy International Picture Thread

    Proof barrel is still hammering with the 140 Hybrids. Excluding the first shot, which still shows the exact same low right position it has the last 8 times I’ve tested removing the barrel over the last month or two, I can’t remember the last time I put down 4 consecutive groups in the .3’s.
  4. S

    Vibe tumbler media options

    I tried the roasted buck wheat for a while (pure, didn’t mix it). It was great for a few cycles, but quickly started falling apart and would coat the brass in an adhering powder that was a pain to get off. It was also much harder to get stuck pieces out of primer pockets, though it happened with...
  5. S

    WTS- Spuhr A-0011 and A-0015

    The Venom is sold, but I still have the Spuhr mount and riser. The correct part numbers for them are A-0011 and A-0015. Looking for $40 shipped for them.
  6. S

    WTS- Spuhr A-0011 and A-0015

    I don’t have it with me right now but it should be A-0011 and A-0015
  7. S

    WTS- Spuhr A-0011 and A-0015

    Up
  8. S

    Accuracy International Picture Thread

    I’ve got a Bartlein gain twist blank coming in today. I’m finally going to try out both the gain twist and the 6BR, both of which I’ve been interested in for a while. If anyone is interested, I grabbed one of the heavy palma blanks that Altus has stocked (I’ve decided if I never preorder or...
  9. S

    22-250 Barrel twist help

    I’m not an expert on gain twist barrels, but from what I know of their effects this might be a perfect application for one. Obviously you can’t get an Xcaliber barrel that is gain twist, so you’d have to get a custom Bartlein, so it may not be something you’re interested in. You may want to look...
  10. S

    WTS- .308 full die set (Redding Type S, Redding Neck, Forster Ultramicrometer, and upgrades) *SOLD*

    @archerforkids someone just sent the payment for the package, thanks anyway
  11. S

    WTS- .308 full die set (Redding Type S, Redding Neck, Forster Ultramicrometer, and upgrades) *SOLD*

    I’d split it up for $100 for the Type S and upgrades, $25 for the neck die, and $70 for the Forster seater
  12. S

    WTS- Spuhr A-0011 and A-0015

    Up
  13. S

    WTS- Spuhr A-0011 and A-0015

    Up
  14. S

    WTS- Giraud Power Trimmer accessories *SOLD*

    I have the following I’m looking to sell. .308 case holder- $25 shipped *SOLD* .223 case holder- $25 shipped *SOLD* Cutter head with blade- $40 shipped *SOLD* I’ll sell them as a package for $60 shipped.
  15. S

    WTS- AMP pilot #11 (.308 and similar cases) *SOLD*

    Getting out of .308 and don’t need this. It’s the AMP pilot #11 for .308 and similar cases. Looking for $15 shipped. SOLD
  16. S

    WTS- .308 full die set (Redding Type S, Redding Neck, Forster Ultramicrometer, and upgrades) *SOLD*

    I’m getting out of .308 and am looking to sell the die set I built that I was using. I’d like to sell it all as a package, but would split up for the right prices. Here’s what I have. Redding Type S FL die Also comes with the following: free floating carbide button kit, Forster .3090” oversize...
  17. S

    WTS- Spuhr A-0011 and A-0015

    The Vortex Venom is sold, but I still have the Spuhr DR-Burris mount and 10 mm spacer. Looking for $30 shipped for them.
  18. S

    Accuracy International Picture Thread

    @M8541Reaper I did, haven’t had any problems. It definitely will effect the bonding material, but it shouldn’t cause any problems if the person doing it knows what they’re doing as far as the pretreatment goes (i.e. they don’t heat it up to 500 degrees for a few hours or something stupid like...
  19. S

    WTS- AIAT/AXSA 16” .308 Barrel w/ Lapua Palma brass *SOLD*

    I’m looking to sell my 16” .308 barrel for AT and AXSA rifles. I’ve been wanting a 6BR barrel for a long time and finally accepted I hate .308 and was only keeping this barrel because of its length. It is a factory AI 1-10” twist barrel that was cut to 16” and threaded 5/8-24, and cerakoted...
  20. S

    AI and 6.5x47 feeding issues

    I shot 6.5x47L in an AT for a couple years with out ever having a single malfunction, and have been shooting it in my new AXSA for the past couple months still with no problems. That was across 1 AT mag and 2 different AX mags. I actually had my first ever feeding malfunction earlier today, but...
Top Bottom
Back
Home
Forums
Merch
Alerts