Search results

Re: Idea! Official DTA SRS, HTI, Covert, Hunter Thread Anyone using an ACI on the SRS with a S&B 5-25 on a 40 MOA base? Looking for recommendations on what will fit on the rail under the rear of the scope.

Re: 600 and 950 yard videos with DTA SRS 338 LM nice

Re: 600 and 950 yard videos with DTA SRS 338 LM moved to Range Report & Exterior Ballistics

Washoe county range near Reno NV. Very gusty winds. Dialed 6 mils elevation and 1.3 mils windage at 950 yards. Fun and very challenging conditions. Great range. Highly recommended. Projectile pressure wave and reports. Target at 950 is steel plate just to left of yellow barrel. 4200 ft...

Washoe county range near Reno NV. Very gusty winds. Dialed 6 mils elevation and 1.3 mils windage at 950 yards. Fun and very challenging conditions. Great range. Highly recommended. Projectile pressure wave and reports. Target at 950 is steel plate just to left of yellow barrel. 4200 ft...

Re: Where to buy Manfrotto tripods? Thanks....found a place....ordered.

Need a good tripod for my Leupold Mark 4 spotting scope. Any ideas on where to get Manfrotto's?

Anyone have any reviews on this product?

Re: Some load development Anytime. Now just saving funds for a second barrel and bolt. The bullpup is perfect for completely fitting in my Eberlestock G4 tactical bag. The tactical bag looks like it will also hold the barrels nicely on the long side pockets. One side for barrel and the...

Re: Some load development I have noticed flow on everything I have shot including factory Lapua 338 ammunition (i.e. non-reloads). If I remember correctly if I looked at the bolt face the firing pin hole seems to be larger in diameter than the firing pin by an amount similar to the flow...

Re: Some load development I'll follow up Penguin's post by adding my own load development Date: 1/10/2011 Time: 2pm Location: Northern California Rifle: DTA SRS w/ DTA 338 Lapua barrel Elev: 146 ft Humidity: 58% Temp: 48 F Light: Overcast Wind: 5-10mph at 45 degrees Bullet: 250 gr Lapua...

Re: DTA SRS Scope Placement Thanks guys. The consensus is clear.

Re: DTA SRS Scope Placement Thanks Dogtown. That is the same place I have mine except I have two spacers in the stock instead of the three that you have. How is your eye relief and x25 in prone?

Where are you guys running yours? I have the end of my S&B around the location of the start of the composite stock on the top and with two spacers (one removed) I measure approximately 11 inches from end of scope to end of stock. This feels right on the bench but I did a little playing around...

Re: one last question before ordering my S@B Well I finally checked my S&B and it is P4F. The images on that last link are not an exact representation of the line widths when comparing with my eyes but they are close and illustrate the comparative differences.

Re: VIC-123 That is really nice. I was picking out single grains myself by hand.

Just received mine yesterday for some 338 Lapua reloading. Very pleased with the unit. At first I was a little confused as to why closing the lid would change the zero but after reading the instructions it says to keep the lid open during measurements. I found I had to adjust the leveling...

Re: DTA SRS OAL 338 Lapua - What are you measuring? Thank you. My bad. I am running the Lapua 250g scenar HPBT. Anyone have COL for this in their DTA SRS? I'm not familiar with the 250g game king but assume the dimensions must be different.

Re: Bench Shooting Thanks guys. I'll try this when I go to the range on Friday.

Re: one last question before ordering my S@B Ok. Just looked through my S&B with the ordered P4F but after comparing the photos in the link I am wondering if I have the P4F. My lines do not appear as thick as those showing the P4 but may not be as thin as that showing the P4F. I guess the...