Search results

how is the eye relief(wearing eye pro) with the fixed 30? is it about the same as setting it to 30x on the 20-60?

Re: Locktite or Anti-Seize torque it down with a torque wrench. 15 INCH lbs. blue loctite can be removed without damage to the heads. red loctite requires heat. just make sure you read the label and get the removable version.

Re: Locktite or Anti-Seize loctite. you do know anti-seize is a lubricant right?

Re: Rough area on new B&C stock - is this normal? Normal. But i would also check to see if the bolt handle makes contact with the bottom of the notch. Every stock i've used needed to be opened up a bit. From B&C to MCM's. And everyone in between. I just do this to insure consistent lock up in...

Re: My Lucas Bore Guide Arrived Today <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: RacingMars</div><div class="ubbcode-body">I received mine as well. I have what is probably a dumb newbie question -- the bore guide comes with two pieces: one that is the bore...

Re: Can a timney trigger cause light primer strikes? the sear is easily replaceable. look for the pin the sear is hinged on, using the proper sized punch, push out the pin from left to right. you may need to slightly tap the punch. and watch out while punching it out, it may end up running...

Re: Cleaning rod length? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Fixr</div><div class="ubbcode-body">My rifle has a relatively high cheek rest, so I measured the overall length of the rifle(48") to determine what length rod to buy. At that length choices...

Re: forster case trimmer I run mines on a small rigid cordless. Compact and plenty of power

Re: premier optics works for me, strange..

Re: premier optics http://premierreticles.com/

Re: first time timney 510 install and seer came out lol that may have came out the old trigger.

Re: first time timney 510 install and seer came out Theres only one sear spring in the 510. Look in the trigger assembly and youll see a round hole where the spring will sit into, find the correct fitting spring that will fit exactly into it

Re: LT-104 digging/gouging EGW R700 rail + hi-res pics if you have a digital caliper can you measure the width of the slot on the rail? and then measure the nub on the larue mount that goes into said slot? looks like one of the items is out of spec. if both are are in normal spec i'd say ur...

Re: DBM and inletting? lot of DBM's out there to choose from, you got: badger ordnance, CDI, R&D presicion, atlasworx? HS precision, wyatt, and a few others i can't think of. HSP and wyatt are drop in units. most others require inletting, you will need to open up AND deepen the space for the...

Re: Otis Technology Breech-To-Muzzle-Cleaning System i keep a otis cable, a few patches and solvent in my stock pack. comes in handy alot of the time. like when you get a gust of no value sand storm in the face shooting prone. nice to have something a can swab out the bore with in a pinch.

Re: Impact Data Books Paper? i've also found that the ink in a basic BIC pen works the best. no ink bleed/smudge when wet. the gel ink pens like pilot g2's were the worst. even the ink in my fisher space pen didn't fair to well, i think the rite in rain pens might be using the fisher refills...

Re: Impact Data Books Paper? 80wt will give you a thick sturdy feel but data may become smudged when it gets wet. the rite in rain paper is about the same thickness and weight of printer paper, a bit more prone to tearing, but when contacted with water data wont smudge. i've taken a sheet...

Re: if $ is no issue, what's your base/ring setup? Badger, i've never felt the need to buy anything else.

Re: What is type of "fill" for a McMillan stock? Yea the wieght difference is achieved from a different density of material. And not only that, but it is molded into the stock in a certain area to distribute wieght. Interesting thing is, my sniper fill USMC A4 is lighter than my other A4 cut...

Re: Remington 5R Recoil Lug did the previous owner bed the stock?. i would just hog out the recoil lug area in the stock, remove some material in the reciver area and bed thw whole set up