Search results

I've had a lot of success this past year using my pump pillow as a rear bag while shooting prone. I kind of wedge it into/under my armpit, and use it to support my shoulder, head, and buttstock all at once. It sounds awkward and definitely not the first thing people would think of as a rear bag...

I've got one in my Grey Birch 10/22 build. Very solid, holds the action snug. Prefer the rear tang setups, but the cross bolt works well. Not compatible with kidd recoil buffer with the steel pin/rubber sleeve. The chassis only captures the bottom ~1/16" of the buffer, and the steel pin in the...

I don't use a Cronus, but I have an Ares ETR with the same 32 mrad of elevation on my Vudoo in an MPA. It is on a 30 moa rail and I use the Burris XTR rings that have another ~32 MOA in them for a total of around 62moa. My rifle is zeroed at 32m without issue. You'll have no problem with a 40...

Hello from the coast! I've got the rifle zeroed at 32m, and I have 31.7 mrad left in the turret to dial up. Let's me dial to just over 500m with standard velocity ammo. Not sure what exactly I have left down, I didn't check before I set the zero stop, but there won't be much.

Athlon Ares ETR in 1.5" Burris XTR rings, 30 MOA rail and another ~32MOA from shims in the rings.

I have a 30MOA rail and approx 32 MOA extra cant from Burris XTR rings holding my Ares ETR. My rifle is zeroed at 32m, and I have 31.6mil in my turret. So 60MOA rails can work. I don't shoot NRL22, but most of our matches put the bulk of the targets in the 125m-300m which keeps my image...

Yes. I was having constant (~50%) ejection issues on my 6.5x47 built on a stiller tac30 with a gen 2 razor in a spuhr. I made a slow-motion video of a bunch of cases attempting to eject, and found that basically every single case hit the underside of the spuhr. Half the time, the case would...

I've got a 22" (actual just over 21") spiral fluted kukri in a mpa ba with the mpa front weight kit. Still not enough to balance it - need another ~2lbs out front to get balance point ahead of mag well.

I've been using 5/16" aluminum plates for my targets 250y and beyond. 10"x10" plates are very loud, easily heard at 400y. I've got a full size IPSC in the same material, and it can be heard at 550y, though that was just my son and I practicing by ourselves in a quiet environment.

I have about 62 moa between my base and xtr rings. Zeros at 35y using an athlon etr

I have an ETR on my vudoo in a MPA BA, 30 MOA rail, 1.5" burris xtr rings with approx 32 MOA built into them. Still allows me to zero at 35y, leaves 31.4mrad in the turret, NV bridge doesn't interfere. Haven't had any negative effects yet.

I only ran 11 rounds over the chronograph, but it showed avg velocity of 1080, with an es of 37 and sd of 11. Those were probably rounds 40-51 out of the gun so barrel would have been warm and fouled.

Finally got to join the club. 22" Spiral Fluted Kukri in Cobalt TT Diamond flat shoe Burnt Bronze MPA BA Vortex Razor Gen II 4.5-27 MDT Muzzle Brake The first six rounds out of the gun @25m bore sight (one round at bottom target, adjust, 5 rounds into top target) This was just SK rifle...

I've shot with my rifle canted a fair bit, but most of it has been within 100-250 yards @ 20 - 30 degrees cant, where the adjustments aren't so severe, and the targets are often fairly generous - so I haven't really needed to run actual numbers. If my scope leans to the right, I generally just...