• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. T

    Regulator and gauge mods for Giraud annealer...edited to add volt meter...

    Problem solved. I went to the hardware store and found that the needle valve was the same thread pattern as a 1/8 compression fitting. I got one that had 1/8npt male threads, got a 1/8 F-F, and I'm in business. I used thread sealant on the compression fitting threads and paste on all the Npt...
  2. T

    Regulator and gauge mods for Giraud annealer...edited to add volt meter...

    I tried to do this tonight and got stuck trying to install the gauge in place of the valve. I got the linked 1/8 npt gauge from Amazon. It won't thread in. Seems like the valve isn't a taper on mine.
  3. T

    Swipe marks w/ low powder loads, 260 Rem. What's going on?

    I guess just to the body. It will probably be a few weeks before I can get back to the range I guess I'll just try working up again from a lower charge.
  4. T

    Swipe marks w/ low powder loads, 260 Rem. What's going on?

    The brass was fl resized to mid point on the case gauge. I clean between did the first five rounds, and after the next five. I did not clean the chamber. The guide I'm using has orings so I don't think the chamber was wet.
  5. T

    Swipe marks w/ low powder loads, 260 Rem. What's going on?

    OK, I'll try to hit all the questions. Yes the rigle is a Rem 700 built by LRI with a Bartlien 5r barrel. No I didn't chrono, because I left the darn tripod at home. Next time. I took measurements of my brass. Resized is .294" (using Redding dies with bushings), With a bullet 0.296", fired...
  6. T

    Swipe marks w/ low powder loads, 260 Rem. What's going on?

    So I'm trying to work up the load for the 260 Rem I had built in the LRI group buy. Brand new Lapua brass, H4350, CCI BR primers, 142gr SMKs 0.025 of the lands. The Hodgdon website has the load listed as 41.5 to 44.5gr H4350. So I loaded up the whole range in 0.5gr increments. 41.5gr had no...
  7. T

    Rifle Scopes Could use some help from people with astigmatism

    Some very good insights here guys. I also have this issue. I've got great 20/20 or better vision, but astigmatism is a PITA with some sights. Scopes aren't bad for me but Eotechs are really fuzzy, Aimpoints only a little better, and I always have a heck of a time focusing on the front sight of a...
  8. T

    David Tubb Final Finish for Remington 700 SPS

    Would you do this on a new, high quality barrel like a Bartlien?
  9. T

    auto progressive press with external powder measure

    The Dillon RL450 powder die. The also have a funnel for it, and you need to get the insert for the caliber your loading. Dillon Precision: Reloaders, Reloading Equipment, Bullet Reloading, Bullet Reloaders
  10. T

    Use IMR 4320 for 260 Remington?

    Does anyone have any load data for IMR 4320 and the 260 Rem. I'm putting together a new rifle in 260, never loaded for it before. With H4350 impossible to find right now, I need to use what I've got available. I have Varget and IMR 4320 on hand. I'm looking at ordering some Lapua Scenar...
  11. T

    New guy from VA

    Well, I've read a thing or two here over the years and decided it's time to jump in. I've been pretty addicted to ARs for the last 5 or so years. Spend a lot of time on ARFCOM. I've done a bit of 3 gun shooting at Blackwater (or what ever they call themselves now). I've had a Rem 700 308...
Top Bottom
Back
Home
Forums
Merch
Alerts