Search results

Search the forum Search Articles
  1. TBK

    Xero C1 Pro - v3.30 update

    @Garmin I had missed shots yesterday. It was frustrating because it was during load development. I did not realize that shots were missed until I was done so the session and ammo was wasted. It missed 2 out of 30 shots. SW Version: 3.32 Number of shots taken vs recorded: 30 taken, 28 recorded...
  2. TBK

    6.5 Creedmoor

    I did something similar. I started with 3 boxes of Berger 144 gr LRHT ammo for break in and to get used to the chassis setup. I then worked up a load and tested for how far off the lands with 1x fired brass. I am up to ~300 rounds on the barrel. Yesterday I loaded up 30 rounds (now 3x fired...
  3. TBK

    Silencer Central, if true Phuck them!

    Maybe but it makes me feelz guud not buying anything from them.
  4. TBK

    After killing unarmed man, Texas deputy told colleague: 'I just smoked a dude'

    I care. But not about everything or everyone any more. Can't fix stupid. I just reload and practice, waiting for the zombie apocalypse.
  5. TBK

    Of all the parameters that must be met when reloading, what do you think is most important?

    Yup. I tested a batch yesterday loaded up on my old Hornady single stage press. I used AI to recommend a load for my components. I had a box of 50 new Hornady cases and Hornady ELD Match 147gr bullets. (6.5CR) Since the brass was new, I did not want to spend time working up a load. Yesterday was...
  6. TBK

    Of all the parameters that must be met when reloading, what do you think is most important?

    Adding powder before seating the bullet. Had my first squib today. :rolleyes:
  7. TBK

    AW mag feeding issues.

    Just take your time. Adjust and test, repeat as needed.
  8. TBK

    AW mag feeding issues.

    If I remember correctly, I moved the front lips out a little. I grabbed the lips with the pliers. I can't say if it lifted the lip or just pushed the wall out. I did not move it much. The issue I had was that the bullet tip would move forward below the feed ramp and the bolt stopped. This all...
  9. TBK

    AW mag feeding issues.

    They seat similar to those shown by @6brshooter in post #10
  10. TBK

    AW mag feeding issues.

    Here is where I wound up. It is in a VisionPro chassis. If I remember correctly, I adjust the mag catch to its highest level. The mags have no slop in the chassis. Setting the front wider allow the tip to rise up right into the chamber as I move the bolt forward. I didn't measure it before so I...
  11. TBK

    AW mag feeding issues.

    I had the same issue with my Impact and AW mags. I did not have a tool so I put some painters tape over the mag lips and used pliers to open them up a bit. I also adjusted the mag latch up. I took baby steps, test after each adjustment. Smooth since...
  12. TBK

    Zero press Gen2

    If one were buying new today, Gen 1 or Gen 2? I currently use an older Hornady single stage. I am looking for a turret style for precision rifle reloading (Redding T7 or Zero). I don't (up to now) use the press for primers.
  13. TBK

    Eurooptic.com?

    Agree. I emptied my cart and shopped elsewhere.
  14. TBK

    Eurooptic.com?

    And the pay extra for shipper to replace items lost in shiping is there.
  15. TBK

    February 28: A day of defiance by the loony left

    I've been holding up all my purchases until Friday. :sneaky:
  16. TBK

    Trouble shooting - Impact 737 - MDT HNT26 - AW Magazines

    This is what I did with 6.5CR in the 308 AW mags and 737. Is there a recommended width chart for the feed lips? I did trial and error to open the feed lips a little at a time after using all the adjustments on a Vision Pro chassis to have the mag sit nice and tight. It would be nice to have a...
  17. TBK

    Looking for range in Alabama

    I would agree. I am a member. They recently had to send out separate communications to new members--the original did not go.... I might be able to help but I am not sure who to contact. :confused:
  18. TBK

    Looking for range in Alabama

    It is not ready yet but it is being worked on. The Hoover location is shut down. The new Pell City location is open but not complete yet. There have been some weather delays. They have a range map on the web site: https://www.brocksgap.com/clientuploads/directory/documents/New_Range_Map_-_10-24.jpg
  19. TBK

    Biden's Farewell Speech: Your opinion?

    Tuned him out four years ago.
  20. TBK

    Suppressors Better place to buy than silencer shop?

    I buy as an individual; no need for a trust. Local shop was 2-day turnaround from purchase to possession each time. I had a bad experience with Capital (and that’s all I’ll say about it.) I have not found a price difference between online vs local.
Top Bottom
Back
Home
Forums
Merch
Alerts