Search results

Just picked up an PAS AR and the upper has the cocking handle on the side of the upper.{side charging } My question is, is this upper suitable for a "build", either a heavy{ 20-24" 223 barrel } or possibly a 6 CAR [ when brass becomes available again] OR, just leave it as is as "trade fodder" ...

A pop up keep asking me to sign up for PUSH NOTIFICATIONS what is this ???

Any SWAG's on the lead time for an upper from CLE ??

Anyone else seen the X brand powder advertisement on Accurate Shooters forum where X brand advertisement states " BEAT THE HEAT, The most constant velocities across the temperature spectrum ? It's on the Bulletin, after the write up on a 20 PPC pistol

What's the reason for so many RCBS Charge Masters in the classifieds for sale ??

Do you worry about how hot your barrel gets ? The reason I ask is that the range ** I watched two shooters , both shooting 6 CM's, they would shoot 5 rounds in about 4 min. then one had an IR thermometer and he would check both barrels and they would also point to temperature strips on their...

Putting a PRS weapon together for my grand daughter,as soon as I put LH in any search, my options are limited.Right now my options in my price range seam to be the KRG "bravo" and the MDT Oryx. I know her small hand grip an AR grip with no problem, not sure about the Bravo's grip ? Going with...

Using the suggested info form; Platform; rifle in either 6 or 6.5 Use; Florida sunshine, 100 & 300 yd load development on paper, then 600 to 1200 on steel, ALL shot from a bench Other rifles have SFP 40 x scopes with mil dots, usually backed down to 34-36X for 300 to 600 yd. steel 2022 budget is...

Is any one attaching padding / covering to your cheek weld / rest area ? And if so , what are you using ? Thank you

Are McFarland gas seal rings all the same , or are they brand specific ? I thought I'd ask here before going through some of the "big box" stores looking. I have an Armalite AR-10-T I used as a build. I've contacted Armalite, but haven't herd back from them. I've read that IF the bolt stays...

is there a "constant" that can be used to convert CUP listings into PSI's ?

Does anyone have any experience with this scope ? It meets all of the criteria but one for a 600 yd. steel plinker I'm setting up for my daughter. Criteria; 30+ max power, shooting from a bench at steel out to 600 yds using a 6 CM LH bolt gun., Max is $500.00 This scope is 8x34x56, FFP with...

Are there any, other that RRA uppers that are compatible with an RRA LAR-8 lower ?

A while back on another forum there was a barrel rankings chart,call them Tier 1, Tier 2, Tier 3. Now for the most part these were just personal opinions , but repete usage says a lot. Also, some shops selling barrels AND pre-fits only handle Tier 1 barrels , "bugholes"being one. Your comments...

I see those that build and sell 6AR ,6 ARC, ect.list using STIFFER uppers, and I'm wondering if this is just a selling ploy, since there are so many DIY 6 and 6.5 Grindle size case AR's built from a varied selection of uppers

Does anyone have or seen DIY plans to Adapt something wide & flat to an AR forearm ?

ALL of the "standard" powders for the 6 & 6.5 CM are not to be had anywhere. As alternatives has anyone used Norma 204, or VVN 550 or 555 ? And if you have , any problems using SRP's {7 1/2 of 205M}

Doing some internet searching I came up with , the Marine Corps used a 1-12 twist up to the m40's through the Mk 5 or 6. And the Army used a 1-11.25 on all their M 24's. 1-12 twist Bbl's seam to be easier to find. What are you'll using ? V/r

Besides the obvious $$$$, is there much of any difference between the LPR and the LPR 2.0

I did the search thing, found a $hip pile of WTB / WTS posts. Is this the one you'll have ? I've seen reference to a 1500, is that the old version and this one the new and improved ? For those who use "LOG" type powders like 4064, 4198, ect. how much of a (+ - ) does your unit vary with the log...