- Thread starter padom
- Start date
Glock 17 & 34
Xtreme copper plated 115gr round nose
Win small pistol primer
mixed brass
4.3gr Titegroup
1.13" OAL
1120 FPS
Xtreme copper plated 115gr round nose
Win small pistol primer
mixed brass
4.3gr Titegroup
1.13" OAL
1120 FPS
Here my very accurate and stupid quiet 9mm subsonic load
Glock 19, SIG 229, MP5, AR9
Xtreme 165gr
1.165" COAL
CCI SPP
3.8gr VV N340
914fps SD9 over 30 shots
Glock 19, SIG 229, MP5, AR9
Xtreme 165gr
1.165" COAL
CCI SPP
3.8gr VV N340
914fps SD9 over 30 shots
Last edited:
115 gr FMJ or JHP
4.8-5.0 N330
4.8-5.0 N340
5.3 WSF
4.2-4.3 HTG
These all worked well as 9mm service pistol loads when I was in the process of legging out. Each one proved to be 50 yard accurate.
4.8-5.0 N330
4.8-5.0 N340
5.3 WSF
4.2-4.3 HTG
These all worked well as 9mm service pistol loads when I was in the process of legging out. Each one proved to be 50 yard accurate.
Hornady 124gr XTP - Starline Brass - CCI #500's - 7.1 grains of AA#7 = 1125fps out of a G17 G5 and a Sig M18 @ 60° F
1/2" of barrel length difference between the two meant nothing.
I did have several of the batch make it into the high 1140's.
The previous session was fired in 75°'ish temps and the average velocity was a bit closer to 1150fps
I like this combo for all year, w/o worries of pressure spikes.
On a 100 degree day, with the sun beaming down on your holstered pistol, i am not too worried about pressure spikes.
Though i will try it in those conditions to be certain. (Next year)
1/2" of barrel length difference between the two meant nothing.
I did have several of the batch make it into the high 1140's.
The previous session was fired in 75°'ish temps and the average velocity was a bit closer to 1150fps
I like this combo for all year, w/o worries of pressure spikes.
On a 100 degree day, with the sun beaming down on your holstered pistol, i am not too worried about pressure spikes.
Though i will try it in those conditions to be certain. (Next year)
What was your COAL for them?
Not bad but you should consider N330 if you can find some with those 165gr.
I do 3.3gr with the Bayou 160 @ 1.155" coal. Very soft.
Brass Monkey bullets 137gr RN Coated
Winchester spp
Range pick up Brass
4.0gr CFE Pistol
COL 1.1
131 PF
Winchester spp
Range pick up Brass
4.0gr CFE Pistol
COL 1.1
131 PF
So found a box of Rainier 147g hp 9mm. (600 ea)
having trouble deciding coal and no viable listings.
Basically a coal of 1.100 or 1.130 but lack of consensus bugs me.
These will be standard rounds not +p. probably 3.3 -3.4 W244 at 900 - 930 fps.
Any help would be appreciated.
having trouble deciding coal and no viable listings.
Basically a coal of 1.100 or 1.130 but lack of consensus bugs me.
These will be standard rounds not +p. probably 3.3 -3.4 W244 at 900 - 930 fps.
Any help would be appreciated.
I just finished up a load with the DG 147gr Flat Point BB Hi-Tek bullets. My COAL: 1.130 My best load was with Unique and Viht N330.
Single favorite 9mm load. Zero 147 JHP, 4.0 WSF, CCI spp, 1.10 coal.
Factory Federal American Eagle 147gr. Flat Point Subsonics through my MP5 @ 100 yards... It even start putting down some consistent hits at 200 yards once I found my POA with the irons. I'm very impressed with the consistency for pistol ammo.
H&K MP5 @ 200 yards with iron sights...
Thank you so much !
Looks pretty much same!
It's exactly 3.8 grains , on 100 grains bullet.
This is not factory ammo , this is remanufactured 9mm load maded for PCC with 100 grain berrys holow base bullets.
I opened one and try to recognize powder.
