Anschutz 1727 magazine basepads

[Adam B]

I just picked up one of these rifles and the Achilles’ heel of it in my mind are the magazines. You’re forced to do a reload on a 12 round stage. Is anyone currently printing magazine extensions? I tried to get my L3 I magazine extension for my CZ to work and it is a no go.

 

[oldrifleman]

I have not found one

 

[shoot4fun]

I have not found one

Anschutz Magazine Extension for 54 / 64 / Fortner Actions | eBay

Magazine Extenstion for Anschutz 1420-U13 Magazines. Requires use of follower and spring from CZ 455 10 round poly mag (#12004) or Savage mk2 10 round mag ( #20005) - either follower will require bending (CZ) or trimming (Savage) to tune the fit for proper function.

www.ebay.com

I bought a couple of these. Wound up having to buy two Savage mags to rob the springs and followers. Then there is some minor fitting to the follower.
Do they work? So-so at best with a full 12 rounds. If you have never owned an Anschutz then be advised that the magazines are not perfect. Mine run great 99.5% of the time but you must take care not to get "rim-lock" when loading them. In fact, in the downloadable manual it has a section devoted to loading them.
I wish, even with what seems to be some issues, L3i would come up with a plus rounds mag for the Annie.

 

[Criver600]

Anschutz Magazine Extension for 54 / 64 / Fortner Actions | eBay

Magazine Extenstion for Anschutz 1420-U13 Magazines. Requires use of follower and spring from CZ 455 10 round poly mag (#12004) or Savage mk2 10 round mag ( #20005) - either follower will require bending (CZ) or trimming (Savage) to tune the fit for proper function.

www.ebay.com

I bought a couple of these. Wound up having to buy two Savage mags to rob the springs and followers. Then there is some minor fitting to the follower.
Do they work? So-so at best with a full 12 rounds. If you have never owned an Anschutz then be advised that the magazines are not perfect. Mine run great 99.5% of the time but you must take care not to get "rim-lock" when loading them. In fact, in the downloadable manual it has a section devoted to loading them.
I wish, even with what seems to be some issues, L3i would come up with a plus rounds mag for the Annie.

With some attention to detail, and careful assembly they work perfectly. You have to modify the savage follower. Great 12 round magazines.

 

[Adam B]

Awesome! Thank you very much!!

 

[Adam B]

So do I have to buy Savage magazines and steal the followers out of them?

 

[Criver600]

So do I have to buy Savage magazines and steal the followers out of them?

Magazine Extenstion for Anschutz 1420-U13 Magazines

****Requires custom fitting of CZ or Savage follower and spring!****

Design Features:

• Adds at least +2 capacity (loading past 12 may reduce reliability)
• Developed with input from US Precision Rifle National Team members
• Access ports at front and back of extension to make sure spring is seated properly
• Requires use of follower and spring from CZ 455 10 round poly mag (#12004) or Savage mk2 10 round mag (#20005) - either follower will require bending (CZ) or trimming (Savage) to tune the fit for proper function. Followers and springs are not included.
• Includes extension and M3 set screw only

Install Instructions:

• Tune follower as needed to fit magazine body
• Install follower and spring in body
• Compress spring to allow extension to slide on from the front
• Slide on extension
• Ensure spring is seated against floor of extension - use holes at front and back of extension to manipulate spring as needed.
• Back out set screw using 1.5mm hex wrench (not included) until 2-3 threads are above rear of magazine to lock it into place.

I used Savage magazines, remove minimum material from the follower. It must travel without binding (at all) the length of the magazine body. Good Luck

 

[Adam B]

You are awesome!

 

[shoot4fun]

Magazine Extenstion for Anschutz 1420-U13 Magazines

****Requires custom fitting of CZ or Savage follower and spring!****

Design Features:

• Adds at least +2 capacity (loading past 12 may reduce reliability)
• Developed with input from US Precision Rifle National Team members
• Access ports at front and back of extension to make sure spring is seated properly
• Requires use of follower and spring from CZ 455 10 round poly mag (#12004) or Savage mk2 10 round mag (#20005) - either follower will require bending (CZ) or trimming (Savage) to tune the fit for proper function. Followers and springs are not included.
• Includes extension and M3 set screw only

Install Instructions:

• Tune follower as needed to fit magazine body
• Install follower and spring in body
• Compress spring to allow extension to slide on from the front
• Slide on extension
• Ensure spring is seated against floor of extension - use holes at front and back of extension to manipulate spring as needed.
• Back out set screw using 1.5mm hex wrench (not included) until 2-3 threads are above rear of magazine to lock it into place.

I used Savage magazines, remove minimum material from the follower. It must travel without binding (at all) the length of the magazine body. Good Luck

You are awesome!

I saw where someone had modified Savage magazines to fit and feed in an Anschutz by doing some creative fitting. To me I would rather spend the $$ on Anschutz magazines. When I bought Savage mags to rob parts necessary use these extensions a quick check of a couple places on the internet showed quite a difference in cost. Got mine from Midway for about $20 each. The extensions will also work with CZ mag spring and modified followers.

 

[ST42]

I run them and have had Zero issues.

 

[shoot4fun]

Oh well, it's only money right?
Just ordered my order 1727 in a red AI ATX chassis and four more 10-round mags.

 

[Adam B]

I shot mine in a match on Saturday other than me mentally fucking up the match; the rifle was a hammer and was amazing to shoot.

 

[shoot4fun]

With some attention to detail, and careful assembly they work perfectly. You have to modify the savage follower. Great 12 round magazines.
View attachment 8679111View attachment 8679112

I ordered two more extensions last night and happened to see the same seller has safety mags with flags so I ordered a couple of them as well. Then, of course, I ordered two Savage 99 mags to rob springs and followers from. The good times never end (until the credit limit is met)

 

[Adam B]

I saw where someone had modified Savage magazines to fit and feed in an Anschutz by doing some creative fitting. To me I would rather spend the $$ on Anschutz magazines. When I bought Savage mags to rob parts necessary use these extensions a quick check of a couple places on the internet showed quite a difference in cost. Got mine from Midway for about $20 each. The extensions will also work with CZ mag spring and modified followers.

Tried this and couldn’t get it to work. What magic do I need to do?

 

[shoot4fun]

Tried this and couldn’t get it to work. What magic do I need to do?

Savage 99 or CZ spring and follower?
The followers have to be trimmed. There is a YT on it that shows how but I didn't find it very helpful.
The Anschutz magazine has an indention on either side at the top rear. you will need to trim the follower so it can come all the way up on the mag body.

 

[Adam B]

Savage 99 or CZ spring and follower?
The followers have to be trimmed. There is a YT on it that shows how but I didn't find it very helpful.
The Anschutz magazine has an indention on either side at the top rear. you will need to trim the follower so it can come all the way up on the mag body.

I tried to modify a Savage MK2 magazine to fit in the Anschutz. The modification of using the savage internals in the Anschutz works like a charm after you modify the follower.