How Hard is it to put in the detachable mags bottom mtal made by Badger and ACIS? Would it be a project that i could do on my own or should i send it off. I have limited armor skills from the Air Force but not a gun smith.
Re: Bottom metal
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: POPEYECOP</div><div class="ubbcode-body"> I have limited armor skills from the Air Force but not a gun smith.</div></div>
I would send it out then.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: POPEYECOP</div><div class="ubbcode-body"> I have limited armor skills from the Air Force but not a gun smith.</div></div>
I would send it out then.
Re: Bottom metal
AICS stock has DBM built in, no fitting needed.
Badger DBM there are mixed experiences, some have not had a problem installing it themselves, and others had problems. What stock do you have? If you don't have one yet and you're looking into McMillan or Manners, you have order it with Badger inlet and it should be a doable DIY job.
AICS stock has DBM built in, no fitting needed.
Badger DBM there are mixed experiences, some have not had a problem installing it themselves, and others had problems. What stock do you have? If you don't have one yet and you're looking into McMillan or Manners, you have order it with Badger inlet and it should be a doable DIY job.
Re: Bottom metal
If you go with CDI precision bottom metal he will inlet for $50 and do a perfect job. I do alot of my own stuff but after doing one bottom metal I sent the other one out to Jeff.
If you go with CDI precision bottom metal he will inlet for $50 and do a perfect job. I do alot of my own stuff but after doing one bottom metal I sent the other one out to Jeff.
Re: Bottom metal
+1 to what were said... Don't spend the money to inlet your factory sps stock for bottom metal; it is just not worth it.
I plan to get a B&C light tac stock and have Jeff at CDI inlet it for his bottom metal for a budget build.
+1 to what were said... Don't spend the money to inlet your factory sps stock for bottom metal; it is just not worth it.
I plan to get a B&C light tac stock and have Jeff at CDI inlet it for his bottom metal for a budget build.
Re: Bottom metal
Pete thats exactly what I did, cerakote is curing on both right now and Im sitting at $450 for the finished stock. For my needs that sure beats $500 for the stock and another $300 for bottom metal.
Pete thats exactly what I did, cerakote is curing on both right now and Im sitting at $450 for the finished stock. For my needs that sure beats $500 for the stock and another $300 for bottom metal.
Re: Bottom metal
Phoenix and Pete thanks for the info. I think I will go that route with a Bell & Carlson. I checked out CDI web site and found that they are very reasonable on the work they do.
Phoenix and Pete thanks for the info. I think I will go that route with a Bell & Carlson. I checked out CDI web site and found that they are very reasonable on the work they do.
Re: Bottom metal
Small hijack here, but since we're on the subject.
I didn't know CDI made bottom metal until a few days ago. It looks very similar to the Badger M5. Are the footprints of each different, and if so, in what way??
CM
Small hijack here, but since we're on the subject.
I didn't know CDI made bottom metal until a few days ago. It looks very similar to the Badger M5. Are the footprints of each different, and if so, in what way??
CM
Re: Bottom metal
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Norcal Phoenix</div><div class="ubbcode-body">Pete thats exactly what I did, cerakote is curing on both right now and Im sitting at $450 for the finished stock. For my needs that sure beats $500 for the stock and another $300 for bottom metal. </div></div>
Apologies to the OP for another hijack, but Norcal would you mind posting some pics post ceracoat? Thanks in advance!
I had the same thought process as you... I could either get an AICS or McRee for a drop in solution, a McMillan or Manners + bottom metal + pillar & skim bedding, or the B&C + CDI + skim bedding at the cheapest. I am going with the latter...
I will have to open up the barrel channel on the Light Tac a bit but I can do that plus bedding on my own to save even more cost.
Oh and may need to add a Karsten to the B&C but that is another DIY project.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Norcal Phoenix</div><div class="ubbcode-body">Pete thats exactly what I did, cerakote is curing on both right now and Im sitting at $450 for the finished stock. For my needs that sure beats $500 for the stock and another $300 for bottom metal. </div></div>
Apologies to the OP for another hijack, but Norcal would you mind posting some pics post ceracoat? Thanks in advance!
I had the same thought process as you... I could either get an AICS or McRee for a drop in solution, a McMillan or Manners + bottom metal + pillar & skim bedding, or the B&C + CDI + skim bedding at the cheapest. I am going with the latter...
Oh and may need to add a Karsten to the B&C but that is another DIY project.
Re: Bottom metal
Here are some shots of the light tactical running the CDI bottom metal. There is a little room at the front and back based on the radius of the stock but its purely cosmetic. If I was feeling really anal about it Im sure it would take about 5 minutes to make everything perfect. $450 is a tough deal to beat for a good stock with some excellent bottom metal fitted. This fit job was $50 from Jeff at CDI.
Here are some shots of the light tactical running the CDI bottom metal. There is a little room at the front and back based on the radius of the stock but its purely cosmetic. If I was feeling really anal about it Im sure it would take about 5 minutes to make everything perfect. $450 is a tough deal to beat for a good stock with some excellent bottom metal fitted. This fit job was $50 from Jeff at CDI.
