I removed the trigger assembly from the action and just need some assistance on putting it back on the action. Is there any pics of this somewhere? I tried searching with no results.
Gunsmithing How to Trigger assembly please?
- Thread starter bdh308
- Start date
Re: How to Trigger assembly please?
Xmark pro on a Remy700 308win. I got a couple of small parts like the spring and hammer and obviously cant remember how it goes back. Thanks.
Xmark pro on a Remy700 308win. I got a couple of small parts like the spring and hammer and obviously cant remember how it goes back. Thanks.
Re: How to Trigger assembly please?
No hammer to be had on these triggers. I'm assuming you're calling the sear a "hammer".
So you have the 2 pins to hold the trigger to the action, a coil spring, and a silver piece with one end rounded and the other end sort of hooked?
Anything more to assemble?
No hammer to be had on these triggers. I'm assuming you're calling the sear a "hammer".
So you have the 2 pins to hold the trigger to the action, a coil spring, and a silver piece with one end rounded and the other end sort of hooked?
Anything more to assemble?
Re: How to Trigger assembly please?
Yes. I figured out wear the sear and the small coil goes. Now Ive got the long pin type spring to hold the trigger in but not sure how to install and keep the sear and coil from popping out.
Yes. I figured out wear the sear and the small coil goes. Now Ive got the long pin type spring to hold the trigger in but not sure how to install and keep the sear and coil from popping out.
Re: How to Trigger assembly please?
Gonna be honest with you, it is a bitch to put back in if you haven't done it before. You'll feel like you need three hands. I always thought it was easier to put the forward pin in first where the spring is, and then put in the rear pin. You'll have to play with it, cuss hard a few times, and then play with it again.
Gonna be honest with you, it is a bitch to put back in if you haven't done it before. You'll feel like you need three hands. I always thought it was easier to put the forward pin in first where the spring is, and then put in the rear pin. You'll have to play with it, cuss hard a few times, and then play with it again.
Re: How to Trigger assembly please?
This will help. Not an X-Mark but this all goes back in the same way, old style or X-Mark.
This will help. Not an X-Mark but this all goes back in the same way, old style or X-Mark.
Re: How to Trigger assembly please?
Thanks Brian. Very appreciative for your efforts. Problem solved.
Thanks Brian. Very appreciative for your efforts. Problem solved.
Re: How to Trigger assembly please?
Awesome pics Randy. The ones I took didn't turn out nearly this nice. I think I'll use these instead when I go to reassemble.
Awesome pics Randy. The ones I took didn't turn out nearly this nice. I think I'll use these instead when I go to reassemble.
Re: How to Trigger assembly please?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: iflyaaord</div><div class="ubbcode-body">Which pin goes in the forward hole? Short or long? </div></div>
the short one
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: iflyaaord</div><div class="ubbcode-body">Which pin goes in the forward hole? Short or long? </div></div>
the short one
Re: How to Trigger assembly please?
Put the front pin in first as you can't get it in once the rear is in. Pins go in from the left side. Don't worry about the sear spring as you can put it in once the front pin, trigger housing and sear are pinned in place. Put the sear spring in the hole and then lower the sear. I use another punch or suitable tool to hold the end of the sear and housing in place while I start the pin and make sure the mag release and spring are in place.
Put the front pin in first as you can't get it in once the rear is in. Pins go in from the left side. Don't worry about the sear spring as you can put it in once the front pin, trigger housing and sear are pinned in place. Put the sear spring in the hole and then lower the sear. I use another punch or suitable tool to hold the end of the sear and housing in place while I start the pin and make sure the mag release and spring are in place.
Re: How to Trigger assembly please?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: B y r o n</div><div class="ubbcode-body">Put the front pin in first as you can't get it in once the rear is in. Pins go in from the left side. Don't worry about the sear spring as you can put it in once the front pin, trigger housing and sear are pinned in place. Put the sear spring in the hole and then lower the sear. I use another punch or suitable tool to hold the end of the sear and housing in place while I start the pin and make sure the mag release and spring are in place. </div></div>
Thanks a bunch. Doing rifle re-vamp on my 700P and this is one stop along the way.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: B y r o n</div><div class="ubbcode-body">Put the front pin in first as you can't get it in once the rear is in. Pins go in from the left side. Don't worry about the sear spring as you can put it in once the front pin, trigger housing and sear are pinned in place. Put the sear spring in the hole and then lower the sear. I use another punch or suitable tool to hold the end of the sear and housing in place while I start the pin and make sure the mag release and spring are in place. </div></div>
Thanks a bunch. Doing rifle re-vamp on my 700P and this is one stop along the way.
Similar threads
