Rifle Scopes Need 34mm AR Mount

[mattwaage1]

I need a lower 20moa(or so, 15-30moa will work) 34mm AR mount cantilever. Low as in 1.1-1.2" hieght. I have a ADM recon 20moa mount now and the 1.55 height is too high for a decent cheek weld. Looking for options, looked at spuhr but didnt see their cantilever. looked at AAD but their height is 1.45 or so, too bad I would like one of those. Looked at ADM again and their lower mount has no MOA built in.

Suggestions?

Thanks!

 

[mildot326]

Maybe take a look at the KAC mount?

 

[mattwaage1]

The KAC ones on the website are listed at 1.4 high. still would like to get a little lower

 

[mildot326]

I have the Leupold Mark 6 IMS mount, however it has no MOA. I also use Sphur rings, on my bolt gun, they are 1"

 

[Captain Kirk]

You could go with a Alpha or Spuhr for that height and canted. Most "AR" mounts will be in the 1.4-1.5" height range, I ran into this problem looking for a mount for my POF 308 which has a 1/2" taller rail, most mounts were too tall.

 

[mattwaage1]

I thought spuhr use to make a cantilever but didnt see it on their site. my front ring is positioned pretty much right over the upper/handguard seam.

 

[mildot326]

Go to the Mile HIgh Shooting site, they have all the Sphur models. Spuhr does make a cantilever mount.

 

[Captain Kirk]

Their cantilever mounts are 1.46

 

[mattwaage1]

Ah yeah was looking at mile high and found it. seems hard to find a low, cantilever mount with 6mils built in...

 

[Captain Kirk]

Nightforce is rumored to be making a 34mm Unimount for the BEAST, I wonder what the height will be and if or when it will be available.

 

[KillShot]

The GDI mounts have 25moa if you don't mind the price. CS Tactical has a few in stock for $550, which is $15 less than retail.

cstactical

 

[mattwaage1]

The GDI mounts have 25moa if you don't mind the price. CS Tactical has a few in stock for $550, which is $15 less than retail.

cstactical

Know the height on the GDI I dont see it listed on their sight.

 

[KillShot]

It's 1.375 from what I was told.

 

[Toast]

I got a flyer from Midway USA who have the Burris quick detach AR mounts on sale for something like $94.

 

[mattwaage1]

I think burris only makes up to 30mm

 

[mattwaage1]

May wind up going with the low ADM recon and just have to bite the bullet on the built in cant. I am not finding anything. THE GDI is getting pretty close if its 1.375, but its not perfect, and for 500 bucks I have a hard time paying that and settling If you know what I mean. Maybe I should just look into a higher stock for the AR308, but getting the optic closer to the bore would be optimal.

 

[Captain Kirk]

I have also ran Accuracy International mounts on ARs, they are lower and are available in 18moa or 28moa. They dont have the cantilever but its a option

 

[mjh30]

Would the combination of a Badger 22moa rail and Seekins low rings be about 1.35, thinking about throwing my Hensoldt on my flattop sometimes but wanted the lowest option.

 

[mattwaage1]

I cant believe in this day and age I cannot find an optic mount that I want. I figured that I could find a mount that position the scope straight east if I pointed the rifle north.

Turns out the ADM-RECON-SL is not a cantilever mount.

The search continues.

 

[Rem7]

Look at third eye tactical, email Stuart at Osprey Rifles in UK.

 

[224Man]

I would consider adding a stock pack or a Magpul PRS to your rifle. The PRS would let you fine tune the cheekrest, add length of pull adjustment and rear monopod capability for $300 less than the premium scope mounts. I can't imagine that reducing the scope bore offset by .1" per $100 would provide the best accuracy improvement for the money. You may be far more skilled than me, but in my case an extra 300 rounds of practice would provide far more utility.
Regards,
224Man

 

[mildot326]

Maybe give these guys a look? Kyle Lamb uses there mounts.
Alamo Four Star Firearms Accessories