Resize new brass?
- Thread starter tpr564
- Start date
Re: Resize new brass?
I have always resized my new brass just to make sure everything is spot on. I don't know if you "have" to though.
I have always resized my new brass just to make sure everything is spot on. I don't know if you "have" to though.
Re: Resize new brass?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Jeremybj</div><div class="ubbcode-body">I have always resized my new brass just to make sure everything is spot on. I don't know if you "have" to though. </div></div>
Same here.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Jeremybj</div><div class="ubbcode-body">I have always resized my new brass just to make sure everything is spot on. I don't know if you "have" to though. </div></div>
Same here.
Re: Resize new brass?
I always full-length resize new rifle cases.
You can absolutely skip this step if you want to, but You'd be surprised at the variance between cases with respect to headspace and neck tension.
I only chamfer/deburr if there is a need, like after trimming, or if the factory case mouth looks ragged.
I always full-length resize new rifle cases.
You can absolutely skip this step if you want to, but You'd be surprised at the variance between cases with respect to headspace and neck tension.
I only chamfer/deburr if there is a need, like after trimming, or if the factory case mouth looks ragged.
Re: Resize new brass?
I always resize brass to fit my specific chamber. Sizing properly is important step in reloading and I feel helps when optimizing your accuracy.
I always resize brass to fit my specific chamber. Sizing properly is important step in reloading and I feel helps when optimizing your accuracy.
Re: Resize new brass?
Only if your dies are set up right to begin with. If not you might size them down even farther than they already are. Most new brass I have seen is sized too much from the factory to begin with.
Only if your dies are set up right to begin with. If not you might size them down even farther than they already are. Most new brass I have seen is sized too much from the factory to begin with.
Re: Resize new brass?
I neck size all new brass. Not only to iron out the dents and oval shaped mouths, but to get the correct neck tension.
I neck size all new brass. Not only to iron out the dents and oval shaped mouths, but to get the correct neck tension.
Re: Resize new brass?
Yes, generally cases come headspaced at the small end of spec.
Sometimes they come "over-bumped" and firing the case is all you can do to fix it.
Factory cases can, and do, come long in the shoulder.
Running through a resizing die, can and does bring the shoulder back into spec with respect to headspace.
If you really want to depend on your ammunition, I can't imagine not doing this step.
I've seen many guns go down because of out-of-spec cases.
A case gauge, and experience, really come in handy when setting the re-sizing die.
If your dies are not set up properly to begin with, you're getting ahead of yourself and have more learning to do anyhow.
I prefer to only have guns with spec chambers so I can interchange ammunition if I want.
At this point, if my chamber had a tight neck, I would change the chamber and not the ammunition.
Yes, generally cases come headspaced at the small end of spec.
Sometimes they come "over-bumped" and firing the case is all you can do to fix it.
Factory cases can, and do, come long in the shoulder.
Running through a resizing die, can and does bring the shoulder back into spec with respect to headspace.
If you really want to depend on your ammunition, I can't imagine not doing this step.
I've seen many guns go down because of out-of-spec cases.
A case gauge, and experience, really come in handy when setting the re-sizing die.
If your dies are not set up properly to begin with, you're getting ahead of yourself and have more learning to do anyhow.
I prefer to only have guns with spec chambers so I can interchange ammunition if I want.
At this point, if my chamber had a tight neck, I would change the chamber and not the ammunition.
Similar threads
