Scope measurements needed

[Glen Seekins]

I am working on a couple of new mounts and want to make sure they will clear everything.
I have what I need from S&B, Nightforce and Leopold

I need some measurements of a few scopes that I don't have and was hoping some of you could help me out. First to post a new scope that's not in the thread gets 10% off their next order until I say I have enough and shut it down.(you can only get the discount once)

30mm, 34mm and 35mm only...

Needs to be measured with calipers, not a tape measure!!!

1) Tube length in the front where your ring would mount.
(From the adjustment housing to where it starts tapering to the objective)

2) The length of the adjustment housing where it contacts the tube.

This is what I am working on. This is just a start, the finished product will be much different. This one is 1.45", 0 and 20moa AR mounts. I want to make sure the front ring is good to go. It is 1.5" long!

AR - X ring

 

[OutlawTen5]

Re: Scope measurements needed

Glen --- USO SN3 3.2-17x44 Ergo w/ 30mm tube dia:

1.) 2.028
2.) 2.044

I'm in for at least one of these. Thanks, Chris

 

[Glen Seekins]

Re: Scope measurements needed

Sweet Thanks

 

[Outsydlooknin75]

Re: Scope measurements needed

Vortex Viper 6.5x20x44

2.85 from adjustment housing to flare of the objective

1.375 for the adjustment housing.

30mm tube.

 

[AlabamaShooter]

Re: Scope measurements needed

Glen, as soon as I get home this evening, I will take some measurements of my SN3 1.8-10 if someone doesnt beat me to it.

 

[Glen Seekins]

Re: Scope measurements needed

Forgot, I need some on the IOR's too with 35mm tubes.

We will have a AR version that goes onto a picatinny rail and a version for R700's that just screw down onto the receiver.

 

[AlabamaShooter]

Re: Scope measurements needed

Glen,

Here are the measurements for my SN3 1.8-10x37 ERGO non EREK 30mm tube scope.

1)1.931 inches from adjustment housing to start of Obj bell
2)1.907 inches for length of adjustment housing. Height of adjustment housing is 1.455 inches(from bottom of small plug in bottom of adjustment housing to top)

 

[TN-MadDog]

Re: Scope measurements needed

Leupold Mark 4 8.5-25X50 30mm tube standard and illuminated.

1. 2.665
2. 1.4

 

[Killshot44]

Re: Scope measurements needed

Nighforce NSX 8X32-56mm
30mm tube
1)2.295"
2)1.654"

 

[BoredEngineer]

Re: Scope measurements needed

USO 3.2-17 44mm TPAL 30mm tube Illuminated

1) 1.430" distance from housing to bell taper
2) 2.844" length of adjustment housing

 

[Brain]

Re: Scope measurements needed

USO SN3 3.2-17x58 ERGO, 35mm tube, Ill. housing

1) 1.950
2) 1.925

 

[Joe Myles]

Re: Scope measurements needed

Super Sniper 3-9x42, 30mm tube
1) 2.250
2) 1.190

 

[KeithR41]

Re: Scope measurements needed

IOR 3-18x44

1. 3.085
2. 2.010

41

 

[TimResin]

Re: Scope measurements needed

NF 5.5-22x56

1. 2.875
2. 1.635

30mm

 

[gugubica]

Re: Scope measurements needed

PRH 5-25

1- 2.026 inches
2- 1.995 inches

2.961 inches from housing to occular assembly.

 

[drmarc]

Re: Scope measurements needed

S&B 5x25 PMII 34mm

1: 1.5300 in
2 1.7855 in

 

[Jumper]

Re: Scope measurements needed

PRH 3-15

1: 1.906

2: 1.960

34mm tube diameter

 

[Glen Seekins]

Re: Scope measurements needed

Thanks guys, This should be more than i need

I will put your names on a list, if you call and order say what you did and they will reference the list. Its going to be your user name on the list...If you have a existing order i will apply it there if you let me know.

10% off to:

OutlawTen5
Outsy
AlabamaShooter
TN-MadDog
Killshot44
BoredEngineer
Brian
Joe M
KeithR41
TimResin
gugubica
drmarc
Jumper