Guys I have been researching for awhile and read almost every post and watched the you tube vids. They all seam so simple to do on a 700. Then I pulled the action and barrel off the FN SPR and looked over the MCM A1 stock. No room for pillars on the pre 64 action w/ DBM in this stock. So how far down the stock does the bedding material go. Just to where the barrel seats on the action or three inches down the stock in the barrel channel?
Gunsmithing Yet another bedding question
- Thread starter mahiman
- Start date
Re: Yet another bedding question
To the recoil lug and not under the barrel chamber.
Some people do 1 1/2" forward of the recoil lug and under the barrel.
I have done a couple and NOT under the barrel and have had great results.
Good Luck.
To the recoil lug and not under the barrel chamber.
Some people do 1 1/2" forward of the recoil lug and under the barrel.
I have done a couple and NOT under the barrel and have had great results.
Good Luck.
Re: Yet another bedding question
I take and wrap the first 2 inches of the barrel with 2-3 rounds of tape.Put tape around the front and sides of the recoil lug.The tape is to give clearance enough to take your action out of stock a little easier when done.The tape on the barrel just keeps the bedding off of the bareel when finished.Make sure and put modeling clay in all holes.And don`t forget your releasing agent.I use devcon for bedding and turtle wax for releasing agent.Some like pledge because you can spray it on.Good luck!
I take and wrap the first 2 inches of the barrel with 2-3 rounds of tape.Put tape around the front and sides of the recoil lug.The tape is to give clearance enough to take your action out of stock a little easier when done.The tape on the barrel just keeps the bedding off of the bareel when finished.Make sure and put modeling clay in all holes.And don`t forget your releasing agent.I use devcon for bedding and turtle wax for releasing agent.Some like pledge because you can spray it on.Good luck!
Re: Yet another bedding question
Just to be sure we're on the same track: http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1167037&page=1
Are you asking if you should bed forward of the lug to compensate for the lack of pillars? In any case, I think 3" is pretty excessive. I stopped in at Lawson's (of stock building fame) before I bedded, and they said they do 1/2-1" max.
Just to be sure we're on the same track: http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1167037&page=1
Are you asking if you should bed forward of the lug to compensate for the lack of pillars? In any case, I think 3" is pretty excessive. I stopped in at Lawson's (of stock building fame) before I bedded, and they said they do 1/2-1" max.
Re: Yet another bedding question
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: mahiman</div><div class="ubbcode-body">Guys I have been researching for awhile and read almost every post and watched the you tube vids. They all seam so simple to do on a 700. Then I pulled the action and barrel off the FN SPR and looked over the MCM A1 stock. No room for pillars on the pre 64 action w/ DBM in this stock. So how far down the stock does the bedding material go. Just to where the barrel seats on the action or three inches down the stock in the barrel channel? </div></div>
I've bedded more Pre 64 Winchesters than I can remember. I just did one here recently on the FN action.
There's always room for a pillar. If not, your using the wrong pillar.
Review this thread:
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=2287936&#Post2287936
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: mahiman</div><div class="ubbcode-body">Guys I have been researching for awhile and read almost every post and watched the you tube vids. They all seam so simple to do on a 700. Then I pulled the action and barrel off the FN SPR and looked over the MCM A1 stock. No room for pillars on the pre 64 action w/ DBM in this stock. So how far down the stock does the bedding material go. Just to where the barrel seats on the action or three inches down the stock in the barrel channel? </div></div>
I've bedded more Pre 64 Winchesters than I can remember. I just did one here recently on the FN action.
There's always room for a pillar. If not, your using the wrong pillar.
Review this thread:
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=2287936&#Post2287936
Similar threads
Gunsmithing
Well it’s stuck in the bedding
