I have a Remington 700 chambered in 6.5Creed with a Trident muzzle device and a Savage Small Shank chambered in 6.5Creed. Both are factory take-offs and both are 20”. Zero rounds through the Savage. 20 rounds through the Remington. $80 each shipped or both for $120 shipped.

Lightly used set of standard MDT Ckye Pod Gen2

$500 Shipped

I have two Harris bipods 6-9" one with the full Area 419 arca upgrades. Other with Area 419 base and rrs arca.

Full 419 upgraded $150 shipped
RRS & 419 $125 shipped

I have an complete upper receiver that has around 400 rounds on it. This Rainier Arms Ultra Match Mod 2 barrel is extremely accurate and will consistently produce 1/2" - 5 shot groups and 3/4" - 10 shot groups with match grade ammo. Barrel has been painted FDE and is very soft shooting with the intermediate gas system. I will list build parts below.
Asking $1000 $850 shipped
No trades please

• Aero Precision upper receiver
• Geissele MK16 DDC 15" handguard
• Rainier Arms Ultra Match Mod 2 Barrel - 16" stainless steel fluted - intermediate gas length - 1/7.5 twist
• Superlative Arms adjustable gas block
• Lantac Enhanced BCG
• Geissele Airborne charging handle
• Area 416 Arcalock mlok dovetail rail - NOT INCLUDED
• Slate black FDE rail panels

ZevOZ9 with Holosun 508T Green, Surefire x300 with box and docs for gun. Comes with 2 mags.

Trade Value-$1500

Looking for a full Kidd 10/22 build. Preferably in a Victor Titan or RPG Chassis.

Showed up, sniffed around a perfectly good trap, pissed on it then proceeded to take a crap while looking straight at the camera.

I have been searching to find a replacement ring cap for the Badger Ordnance or Nightforce 30mm rings. Not the one piece mounts, the older rings. I’d like to put 90* dots on my mk12s and I have come up short.

The 32mm objective (circumference larger than 1.3”) of NXS compact prevents use of the Reptilia stand alone mount. At least as advertised. If I put the 24mm back on, this seems like it would work but the NPR2 reticle is faster for me to hold off than the Mildots.

I’d prefer to not go to one piece mounts for these rifles, as it doesn’t fit aesthetically IMO.

I’m wondering , has anyone used the Nightforce pic rail cap on the 30mm lightweight rings? Curious if it works and how high it puts the the dot.

Had anyone found a solution to mount an RMR or ACRO on older rings?

Brand new mk4hd. Taken out of box to check it out, never mounted in rings. If you’re interested in pics, dm me and I’ll send them over.
$1320 TYD

BNIB internal weight kit for MPA Vanquish.
$125 shipped

Brand new unopened package.

SOLD

Save a few bucks plus tax and shipping from buying direct.




SOLD

Hello, please can some one tell me if I can find some budget after market QD for Picatinny rail that fit Super Cal bipod like BT72-NC?

Chinese or not specifically gun designad are also ok for my usage.

p.s.: I searched on the net the measures of the screws distance and the wide of the junction site fromvthe adapter and bipod head but not luky for me, please can some one tell me this measures?

Thanks

She is one nasty hag!


She described the ammunition control as one that “[refines] how credit card companies track purchases at gun dealerships.”

Hochul noted, “This gives law enforcement the opportunity to find out exactly who may be stockpiling ammunition. And this is an indicator that something untoward could be happening, so it’s an important data point for us to have.”

North Country Now pointed out the credit card tracking will occur via the use of a new merchant code, and that code will allow the tracking of not only ammo purchases but firearms as well.

Currently setup for an AR with the AR cheek piece. But can easily be run on a chassis that accepts a buffer tube, such as the XLR and some MDT chassis. This will include the buffer tube and castle nut, everything you need to throw it on and go.

Asking $200 shipped to you. SOLD

Brand new in sealed box. Looking for $2000 shipped. Insurance would be additional.
Or trade for a nx8 2.5-20 or 4-32. Mil. Fde or od would be nice.
Would also trade for 4-16x42 mil xt f1




these are the best lpvo out there , have a bunch , just need more mag for this gun

LAW Tactical Folder. Hardly used. Has had a few coats of Rustoleum, currently covered in a black finish. Works as is it should. Cleaning out my safe and don't hunt with this particular rifle as much as I planned.

$180 shipped.

SOLD

Excellent condition, all accessories included.

$500 shipped
Zelle for payment

As far as I know after doing a lot of searching on the internet and YouTube, what I'm about to say I have done, has never been done before. On the other hand if it has I wish I would have found it long before now as it would have saved me a lot of trial and error.

I've seen a lot about the new Ruger American Gen 2 rifles so I picked up a couple. The first is a 5.56 NATO Ranch that I installed a Timney single stage trigger in and then dropped the barreled action into a Magpul Hunter stock. The 5.56 has done well which leads to the topic at hand. I picked up the 20" 6.5 Grendel and decided to do the same thing to it only I installed the two stage Timney trigger in the 6.5 Grendel.

The initial Magpul stock was set up for STANAG magazines which wouldn't feed 100% reliably for nothing. Different magazines and even trying to adjust the feed lips of the magazine helped but wasn't a 100% fix. So, after doing some looking I discovered that MDT makes an AICS magazine for 6mm ARC/6.5 Grendel. I also after much to do was able to get the AICS magwell from Magpul. Getting the magwell and then getting it set up and installed so it would work was an absolute dumpster fire and there's no reason for it to be as difficult as it ended up being. My advice if you want to go the route I'm going to continue to explain, buy the Magpul AICS stock or the MDT LSS-XL Gen 2 AICS chassis.

After getting the magwell put together and filing off three tabs on the aluminum skeleton chassis in the Magpul stock I could then effectively use the MDT AICS magazines.

Initial testing was better than expected and got better as I continued to reload the magazine and cycle rounds through the action. There was still a hangup here and there which I was still less than pleased with. It was always the last round that would not feed reliably. Since I load 6.5 Grendel I decided to take advantage of the increased OAL the magazine will accommodate. I determined that a 123 gr ELD-M touched the lands at 2.368" OAL. I then loaded up a dummy round at 2.338" OAL, 0.030" off the lands. I then spent the next five minutes at least loading that dummy round in the magazine and then chamberig that dummy round. It works reliably now without fail.

The long story long of this is, this does work and does indeed improve the rifle. Is it worth it? I can only answer that for me and for me it's definitely worth it. Granted in the end with the magazines, trigger, stock, 20 MOA scope rail, rings, scope, scope level, Area 419 Hellfire brake (I despise radial brakes), I have effectively turned a $550 rifle into a $2,000+ rifle. The added good news though is it shoots various loads quite well and it's not even broke in yet. I'm looking forward to redeveloping loads being able to take advantage of the longer OAL the MDT magazines will accommodate. Hope this possibly helps someone figure out how to make their Ruger American 6.5 Grendel reliable.

Hey guys just shooting this combo l made from parts for the first time today. Had trouble cycling. After looking at it a bunch l noticed this bolt has what looks like an m16 style extractor. All the ar9s I've seen just have the fingerstyle extractor in the lower. So unless I'm missing something I have both. Does any of you know anything about this? Are my observations correct or am I missing something?

I've never been very successful making these. But this time I did a pretty good job. That separation held very tight. It was delicious. Not sure why Tank looks so sad, but I had to get his ass in the background as he fit the subject title so well.

Now do any of you heathens enjoy a good black and tan?

Im new to reloading and finally working on getting my bench setup. I want to make the best use of my space as this is where I’ll setup new rifles and do all my cleaning. The left wall with outlets is all wood and sturdy so I can mount whatever to it, along the back of the long bench there’s an 8-9” gap due to the pillar so I can build shelving of some sort to take up that empty space as well.

I have a rock chucker I’m planning on only setting up with my ugly priming tool, a Forster coax for everything else and a Henderson trimmer. I want to keep all that stuff on the short bench but I’m not sure if I should hard mount all, none, or somewhere inbetween using something like inline fab stuff. One thing is I’d like to get the rock chucker on a riser and leave the other 2 flat. I can put the scale on the long bench where press movement won’t affect it since I didn’t mount the 2 benches together. Recommendations would be appreciated

Leupold MK5 7-35
Larue mount and Leupold ring
Lightly used, no issues
TMR reticle

$1800

Selling this Eotech EXPS 3-0 and G45 Magnifier. Both in excellent condition. Selling individually for $500 each or both for $1,000 shipped.

Only have the G45 left, EXPS3-0 sold.

Hey as anybody dealt with a store in CA called Street gunbroker
Looking to buy a rifle off there website don't knowif they are for

Lookin for a mark 5 lemme know what ya got