Savage SA
PTG bolt head
24" Shilen 1:12 barrel in .20 PPC
NSS nut and lug
Manners folder
CDI bottom metal
Patriot Valley BR/Dasher mag kit
Atlas BT10-LW17
Warne steel rail
AI mount
S&B 5-25 PMII
Group is 10 shots. The first clean bore shot was left, second was just high, the rest made the dot disappear and this is while fireforming 220 Russian brass to PPC!
PTG bolt head
24" Shilen 1:12 barrel in .20 PPC
NSS nut and lug
Manners folder
CDI bottom metal
Patriot Valley BR/Dasher mag kit
Atlas BT10-LW17
Warne steel rail
AI mount
S&B 5-25 PMII
Group is 10 shots. The first clean bore shot was left, second was just high, the rest made the dot disappear and this is while fireforming 220 Russian brass to PPC!
Attachments
What supressor you do use?
Not seem to be Swedish, because it so short, is it Ase Utra?
Remington 700 short mag action - machine work done by APR
28" Bartlein #9 contour 1:8 twist in 7 rSAUM
XLR Element chassis
Trigger tech special
Atlas Bipod
Accurate Mag WSM Magazines
Seekins Precision base and rings
Vortex Viper PST Gen II 5-25x50 mil/mil
SilencerCo Omega break and suppressor
Shooting 180 ELD-Match hand loads
Here she is right after assembly
At the range with the can on
5 round groups @ 300 yards off of bipod and rear bag. Light wind at my back 70 degrees. Best was .68"
The average @ 100 has been right at .25" best was .17"
28" Bartlein #9 contour 1:8 twist in 7 rSAUM
XLR Element chassis
Trigger tech special
Atlas Bipod
Accurate Mag WSM Magazines
Seekins Precision base and rings
Vortex Viper PST Gen II 5-25x50 mil/mil
SilencerCo Omega break and suppressor
Shooting 180 ELD-Match hand loads
Here she is right after assembly
At the range with the can on
5 round groups @ 300 yards off of bipod and rear bag. Light wind at my back 70 degrees. Best was .68"
The average @ 100 has been right at .25" best was .17"
SilencerCo Saker 5.56K
Do you live in Sweden?
Trued 700 short action (.308 Winchester) with tig-welded bolt
Bartlein 1-10 5R, 23 inches
Cerakote Sig Grey
Timney 510 set to 3.0 lbs.
McMillan A5 with DIY cheek riser
BO M5 Enhanced bottom metal
BO 20 MOA steel base (bedded)
Seekins low rings
SWFA 10X42 HD with zero stop shims and Holland level
Not many rounds through it yet but it's holding around .3 MOA with GMM 175.
Last edited:
Big Horn TL3 (DLC coated)
JL Barrel chambered in .308
Manners T4A
S&B 5-25 MSR in Badger Rings
Surefire brake and RC2 762 suppressor (with a not pictured Armageddon gear cover)
GCP_0631 by Greg Connoyer, on Flickr
GCP_0586 by Greg Connoyer, on Flickr
GCP_0942 by Greg Connoyer, on Flickr
JL Barrel chambered in .308
Manners T4A
S&B 5-25 MSR in Badger Rings
Surefire brake and RC2 762 suppressor (with a not pictured Armageddon gear cover)
GCP_0631 by Greg Connoyer, on FlickrGCP_0586 by Greg Connoyer, on FlickrGCP_0942 by Greg Connoyer, on Flickr
My new baby.........GAP Thunder Ranch + Spuhr + AMG + Atlas CAL on way
No, USA for me!
Two of my babies..
Up front:
Hunting rifle, just finished up and tested yesterday
Tikka CTR 308 16"
Crux Nemesis 30
McMillan carbon Game Hunter - Desert Ambush
Mountain Tactical bottom metal - AICS
Steiner Tactical 3-15 in Talley mediums
Southern Precision Rifles 6.5 Creedmoor
Defiant Deviant Tactical action
Mueller Rifleworks 22" barrel
Crux Archangel
Huber trigger
Badger bottom metal
McMillan A5A - McMillan camo
Nightforce ACTAR 5-25 F1 Mil-C in Nightforce rings
Up front:
Hunting rifle, just finished up and tested yesterday
Tikka CTR 308 16"
Crux Nemesis 30
McMillan carbon Game Hunter - Desert Ambush
Mountain Tactical bottom metal - AICS
Steiner Tactical 3-15 in Talley mediums
Southern Precision Rifles 6.5 Creedmoor
Defiant Deviant Tactical action
Mueller Rifleworks 22" barrel
Crux Archangel
Huber trigger
Badger bottom metal
McMillan A5A - McMillan camo
Nightforce ACTAR 5-25 F1 Mil-C in Nightforce rings
Just got my new chassis installed.
Remington 700 AAC-SD 308
KRG Bravo chassis
Weaver 3-10 grand slam tactical scope
barrel style muzzle brake
Harris Bipod
Timney Calvin Elite 2-stage
Remington 700 AAC-SD 308
KRG Bravo chassis
Weaver 3-10 grand slam tactical scope
barrel style muzzle brake
Harris Bipod
Timney Calvin Elite 2-stage
Last edited:
Here are a couple pics of my recent build along with a target from my initial load developent.
6.5 Creedmoor
Cadex Lite Competition Chassis
Cadex DX2 Trigger
Surgon 591 action
Bartlein barrel (26" medium palma)
APA Little B. brake
Vortex Razor HD AMG Scope
Here she is, pretty much all done (ignore the the scope alignment in the pic, it was just tossed in he mount at the time) except a strap on cheek rest to get it perfect. The groups are with 168 and 175 FGMM. I pulled one of the 168's 
Top group pic is a box test with 175s. Shot(1st shot of group), then moved 2mil up(shot), 2mil left (shot), 2mil down (shot) 2 mil right.....then shot 2 back at zero to finish that group. I still need to talk target test and such, but thus far, the AMG definitely returns to zero dead nuts. Off bench with bipod and rear bag.
Gap Thunder Ranch
Spuhr 3601
Vortex Razor AMG (original EBR-7 mil)
Atlas Cal Bipod
Top group pic is a box test with 175s. Shot(1st shot of group), then moved 2mil up(shot), 2mil left (shot), 2mil down (shot) 2 mil right.....then shot 2 back at zero to finish that group. I still need to talk target test and such, but thus far, the AMG definitely returns to zero dead nuts. Off bench with bipod and rear bag.
Gap Thunder Ranch
Spuhr 3601
Vortex Razor AMG (original EBR-7 mil)
Atlas Cal Bipod
Last edited:
Defiance Deviants. 6.5x47 in the manners, .308 in the AX chassis.
Mausingfield M5
ARC Barloc
J Allen 700
24" Proof CF in 6.5 Creedmoor
Bushnell DMR 2 on Spuhr mount
CG Xtreme Mod 22 trigger
Area 419 Hellfire brake
Atlas PSR bipod
ARC Barloc
J Allen 700
24" Proof CF in 6.5 Creedmoor
Bushnell DMR 2 on Spuhr mount
CG Xtreme Mod 22 trigger
Area 419 Hellfire brake
Atlas PSR bipod
The RPR .308 updated with the Paper City handguard
Here she is, pretty much all done (ignore the the scope alignment in the pic, it was just tossed in he mount at the time) except a strap on cheek rest to get it perfect. The groups are with 168 and 175 FGMM. I pulled one of the 168's
Top group pic is a box test with 175s. Shot(1st shot of group), then moved 2mil up(shot), 2mil left (shot), 2mil down (shot) 2 mil right.....then shot 2 back at zero to finish that group. I still need to talk target test and such, but thus far, the AMG definitely returns to zero dead nuts. Off bench with bipod and rear bag.
Gap Thunder Ranch
Spuhr 3601
Vortex Razor AMG (original EBR-7 mil)
Atlas Cal Bipod
View attachment 6898857
View attachment 6898860
View attachment 6898858
View attachment 6898859
Is that new model from Atlas?
I have not seen that before.
Looks very nice, mix of Atlas&Harris.
Atlas "CAL", or "cant and lock" as it doesn't pan.
I think they were released only a few months ago.
I'm pretty happy with it so far.
Dude, sick collection. Some folks think it's ridiculous to have that much cash tied up into a rifle collection. Very nice rifles brother.
Remington 700 5r SA
26” Bartlein 1:8 5r Barrel chambered in 6.5 x 47 Lapua (by Southern Indiana Precision)
Schuler Muzzle Brake (blended to barrel)
PTG Recoil Lug
XLR Element Chassis
Timney Calvin Elite Trigger @ 10 oz.
Harris 6-9 Bipod with Swivel
TPS Steel Base and Rings
SWFA Fixed 16 x
26” Bartlein 1:8 5r Barrel chambered in 6.5 x 47 Lapua (by Southern Indiana Precision)
Schuler Muzzle Brake (blended to barrel)
PTG Recoil Lug
XLR Element Chassis
Timney Calvin Elite Trigger @ 10 oz.
Harris 6-9 Bipod with Swivel
TPS Steel Base and Rings
SWFA Fixed 16 x
His & Her's PRS setups. My 6.5x47 on a deviant (stainless ba, swamp camo t6a)her 6 creed on a kelblys atlas tactical (burgundy ba, grey t6a)
Here’s mine. I put it together myself, it shoots 3/8 - 1/2 moa and I’m proud of it! Posted pics of the typical 5 shot groups.
It’s a PTG trued Rem 700 action with a one piece ptg bolt. It’s a remage setup with a McCrees 6mm creedmoor barrel.
-XLR Envy chassis (tl3 inlet because of the bolt handle)
-Atlas PSR
-bushnell XRS II
-seekins scope base
-badger rings
-shortened badger maximized recoil lug
-hellfire muzzle break
-trigger tech primary
-Tubb speed lock w/ duo spring
It’s a PTG trued Rem 700 action with a one piece ptg bolt. It’s a remage setup with a McCrees 6mm creedmoor barrel.
-XLR Envy chassis (tl3 inlet because of the bolt handle)
-Atlas PSR
-bushnell XRS II
-seekins scope base
-badger rings
-shortened badger maximized recoil lug
-hellfire muzzle break
-trigger tech primary
-Tubb speed lock w/ duo spring
Looks like a well thought out project. Very niceSAC built .300 win mag. Cerokote by shortbus, 28" Bartlein Barrel, Gen 2 razor, like the 215 Berger Hybrid at 2950. Longest hits so far 5 out of 10 at 1640 yards.
R
Rustic1217
Guest
So I've been lurking around the forum as a guest for the past 4 or 5 years. Did a lot of reading and learning. Got into the precision rifle game about two years ago now, started with a Remington 700 SPS Tactical. Shot it a lot and got into reloading to cut cost (shoot more) and squeeze some more accuracy out of the rifle. Slowly upgrading equipment as the funds became available. Now that I finally have something worthy for the forum, here she is: 700 SA .308, 20" barrel, Bushnell 10x, KRG Bravo Chassis. Harris in the mail and pre-ordered Geissele Super 700, hopefully ships sometime this summer.
DT SRS Covert
16" .308 barrel
NF ATACR moa
Desert Tech tapered 30moa rings w/ bubble level
Cadex bipod
Desert Tech .30 brake
Shot a couple .3moa groups last weekend. Its got more in her though. I don't shoot that well.
Thats an awesome paint job! Details of your process?
R
Rustic1217
Guest
Thank you! This is my favorite patterning I've ever done.
So I had to play around with this a bit to get the look I wanted. Base coat of alternating Krylon khaki and sand (6" long sections down the length of the rifle).
Then took strips of burlap that I cut and frayed and wrapped them around the rifle. Sprayed in brown, khaki, and a little od green to fill the gaps between strips but also bleed through the openings in the burlap to get that kind of checkered look. At my discretion just kind of went and re-wrapped a few sections and did that same process again to increase the complexity of the pattern there.
Sorry to hijack! Carry on...
Trued Remington 700 .308
Bartlein 24''
McMillan A3-5
Hawkins Precision bottom metal
Vortex Viper PST Gen II 5-25
Atlas Bipod
All gunsmith work done by Isaac at Southern Indiana Precision (SIP)
Bartlein 24''
McMillan A3-5
Hawkins Precision bottom metal
Vortex Viper PST Gen II 5-25
Atlas Bipod
All gunsmith work done by Isaac at Southern Indiana Precision (SIP)
Here is my latest build. Jon Beanland Sentinel in 6.5x47.
Surgeon 591
26” Hawk Hill MTU 1:8
KMW Sentinel
Jewell Trigger
Nightforce NXS 5.5-22
Dead Air Sandman Ti
Target shown was 825 yards and measured 1.5”.
Surgeon 591
26” Hawk Hill MTU 1:8
KMW Sentinel
Jewell Trigger
Nightforce NXS 5.5-22
Dead Air Sandman Ti
Target shown was 825 yards and measured 1.5”.
Tikka ctr, Krg Bravo, Ase Utra SL7i, Cole-tac Metal phyton cover, Harris bipod, spiced with Hawk Hill custom spiked feets.Falcon M18+ scope.
Big shout out to Joe Ducos for making a great stock into an amazing stock. She shoots as good as she looks, but I wish I had more time to take this little lady out for a good time and do some finger banging.
Just bought this a few weeks ago
Stock Rem 700 action and barrel 300 win mag
Trigger looks like its stock but he has no creep or overtravel about 3 pound crisp break
Precision Armament M11 brake which works awesome
AI chassis with Harris bipod.
AI 20moa rail
Vortex Viper FFP 6x24x50 in Vortek rings
So far I'm shooting new Hornady brass, Hornady 208 bullets, CCI mag primers and H1000 powder.
This is my first Bolt gun and already Im loving it.
Stock Rem 700 action and barrel 300 win mag
Trigger looks like its stock but he has no creep or overtravel about 3 pound crisp break
Precision Armament M11 brake which works awesome
AI chassis with Harris bipod.
AI 20moa rail
Vortex Viper FFP 6x24x50 in Vortek rings
So far I'm shooting new Hornady brass, Hornady 208 bullets, CCI mag primers and H1000 powder.
This is my first Bolt gun and already Im loving it.
Please forward me a closer pic of your fwd rail system and brand. I am looking for options to a Badger EFR part # 306-59. Finding a local smith (Jax- FL) willing to take on a milling a T7 Manners is becoming a challenge. Thank you sir
The EFR is a McCann Industries SIRS EFR. Joe Ducos inletted it for me and did an amazing job too!
https://www.vltor.com/shop/specials-and-sales/mccann-industries-sirs-mount/
https://www.vltor.com/shop/specials-and-sales/mccann-industries-sirs-mount/
Thank you I will have a look.
My Remington 700 Police, all souped up and ready.
Remington usually takes a lot of crap here, but I would say that this one shoots.
5 shots from prone position, 300 meters away. Handloaded Lapua Scenar L 220 grain and VV N170 powder, Norma brass.
And no, it does not look like this every time, but the rifle is a solid sub moa rifle. I have taken it out to 1090 meters, and hopefully I will go even further before this years is over.
Upgraded to a Viper PST Gen2. Loving it so far.
