Good source.
Twist Rate Stability Calculator
Our newly updated Twist Rate Stability Calculator not only tells you what your SG is, but it also lets you know if you are reaching your optimized BC.
bergerbullets.com - Thread starter Subhunter2
- Start date
Good source.
bergerbullets.com 
Criterion 22 Creed barrel coming next week. Anybody have suggestionfor loaded ammo? I see copper creek for mucho dinero.
Been shooting the Berger 85.5's looking for a good load. I've found some accuracy but, today, I had jackets coming apart between 3302 and 3370 over three different charges. You can actually hear the bullet come apart due to the suppressor. I had the 82's over 3500 with no separation.
Anyone else experience this?
Anyone else experience this?
I had 88s explode on me and had some 95s as well due to a carbon ring and I was over 3200 FPS. I think its the difference in the jacket thickness
I got the 80.5s up around 3400 and they held together. Grouped great at 300 yards too
What barrel twist rate on those 85.5 Bergers that are coming apart?
8 twist. I called Berger. The guy wasn't shocked by the 85.5's coming apart at >3500 but was very surprised that I had 82's going over 3500 with no issue. He was going to check with the engineers and see if they've had any reported issues. Although, to be fair, they're so new I might be the first one.
also need this data please
42.5 grains of H1000 gave me 3167fps with the 88.
Hey, dumb question
been dealing with health issues and laziness, havent shot my .22 C with new test loads yet.
How do you know when a bullet comes apart, sound, no holes on the target? I will shoot surressed, will the bullet come apart inside the suppresor and damage it ??? Omega 30 can
been dealing with health issues and laziness, havent shot my .22 C with new test loads yet.
How do you know when a bullet comes apart, sound, no holes on the target? I will shoot surressed, will the bullet come apart inside the suppresor and damage it ??? Omega 30 can
I have a 24 inch 7 twist proof blank on the bench and was wondering if the old 75 amax and the 75, 80, or 88 eldms would hold together or if I should try to get an 8 twist? I do tend to hunt in the cold and about 2200 DA a bit as well.
It happens after the first 20 yards and before 100 yards normally. Nothing on target an a faint Small Greyish cloud will show up for a couple seconds
Just curious what length? I should have a 26¨coming in this week, am curious too. I have Sierras.
Not sure what to tell you, but I have had zero issues with the Berger 85.5’s out of my 26” 8 twist. I’m on my third box of these. I run 40.5 grains of RL17 and they are 3380-3400fps (with suppressor). I’ve worked them out to 800yds so far with amazing results.
I’m usually hunting at 3400-4500 asl with humidity below 30% almost all of the time with temps below 40. With that said, my 8 Twist does really well with the 75 and 80 eldm’s. I get some of my best groups with the 75’s on 37.0 grains of Varget @ 3410fps. The 80’s perform well too with 43.8 grains of Superformance and are about 3520fps.
I ended up getting a 22" 8 twist and trading off my 7 twist. Was worried it would start popping pills down the road.
What dies are you guys using?
Whidden Dies with the non bushing sizer
I don't want to neck turn. Could I get away with fl sizing starline 6 creed or should I try to get gunwerks, peterson, or alpha if i can find it?
Thanks
Thanks
I primarily use Hornady 22 creed brass and just neck size with my hornady ns die (bolt gun). But I also use Hornady 6 creed brass full length sized in my Hornady fl die and trimmed down to length. Both work just fine for me. No issues with either.
I bought 240 rounds of Copper Creek in various weights to try out, then decide on loading or not, Criterion barrel due to in tomorrow, hope it shows up.
Not sure what brass they are using, I will look at it a little closer.
Finnally got to test, mixed emotions an the 7828ssc and H4831ssc . 95SMK shot good but isnt it slow even for a 20" barrel? RL-26 was a little faster. I'm not a speedfreak, love accuracy.
These deformed bullets from tight neck seating shot fine at least at 100 yards
The copper creek 22 creed ammo I bought is using hornady brass but I believe you can have them loaded in alpha as well.
what powder charges are working with the 90gr?? thanks
Thanks guys. Got a 6 creed forster seating die and a whidden 22 creed non bushing die coming. Went with hornady brass to start since I will probably loose a bunch hunting.
Want to say I was around 43.5 on the higher node but I'm not around my notes at the moment.
I talked to redding 2 months ago about something else and asked out of curiosity and they said it’s not anywhere on there radar for future calibers. I hope it changes or if someone else has a positive update I’m happy to say I’m wrong but that’s what I know
Midsouth had some regular full length and neck dies I think.
22 Creedmoor Reloading Dies & Die Sets | Midsouth Shooters
Midsouth carries 22 Creedmoor dies & die sets from your favorite brands, such as Forster, Hornady, & Lee. Browse our selection today at Midsouth Shooters.
www.midsouthshooterssupply.com 22 Creedmoor Reloading Dies & Die Sets | Midsouth Shooters
Midsouth carries 22 Creedmoor dies & die sets from your favorite brands, such as Forster, Hornady, & Lee. Browse our selection today at Midsouth Shooters.
I just googled it and saw that. It’s sketchy on options, but I’m glad they are producing stuff for the 22.
Have you ran any other powders wit the SMK"s?
Is anyone shooting 90gr Sierra Matchkings and either H4350 or Staball 6.5? Or any other larger bullets with those powders?
The case fill on the H4831sc when i hit pressure with the 95smk was maybe 80% case fill so didn't try anything faster
No I haven't, I was pleased with the load and never tried anything else. I'm in the process of having the gun rebarreled so when it returns I plan on trying a few different powders since RL26 is in the land of fairy tales
For the 65, you will want to run Varget instead of the H4350. We run the 69tmk with 39.0gns of Varget and its magic. 3510fps from 20" 9tw. Nearly identical speeds from that load in more than one 20" rifle. You might have to "stand on it" to get the 3600. I would strongly recommend the SRP Lapua brass for that and stay the hell away from Alpha brass, it shows pressure signs way before the Lapua and doesn't give the speed. That is not just my findings either.
I bought my dies from Accurate Arms
no thats not it. damm i'm not at home to check
Mine are Whidden. Horizon FireArms has then too,I believe. Google 22cm.com
Similar threads
