Recent content by AZHUNTER
-
Does custom action make this much difference?
Accuracy in the barrel and Smith. Like your tikka action?, keep it... Want different features pick your custom action and go!- AZHUNTER
- Post #14
- Forum: Bolt Action Rifles
-
Gunsmithing Our latest barrel fluting effort.
Nice! I like the 4ADSR Fluting! 4 Axis, Deep, Spiral, Rectangle.- AZHUNTER
- Post #84
- Forum: The Armory
-
-
Need some D.I.Y. shooting bench ideas...
"We have a few of these on our range, not to difficult to build and really sturdy. https://gallery.mailchimp.com/da7b9fa35ebed8e3151a1e046/files/Shooting_Bench_Plans.pdf " This! i built one years ago and placed in a semi secluded spot for shooting, it was stolen in short order "ass&*@$#"! Great...- AZHUNTER
- Post #11
- Forum: The Bear Pit
-
Gunsmithing Cheap/expedient rust removal?
maybe some Kroil and steel wool.- AZHUNTER
- Post #3
- Forum: The Armory
-
My turn for an annoying "which action" thread
I like my Origin, alot of great features for the price.- AZHUNTER
- Post #69
- Forum: Bolt Action Rifles
-
Best action for the $$$
You get alot of features for the price of the Bighorn Origin.- AZHUNTER
- Post #62
- Forum: Bolt Action Rifles
-
McMillan Mc3 TPIM Stocks? Reviews?
I received a Tradition Standard last month. It is heavier than I expected about 3.5#, from web research I expected it to be about 2.5# and their website is no help since it lists every stock at 4#. I like the feel and design of the stock and it is a ok price, while not a noodle of a plastic...- AZHUNTER
- Post #25
- Forum: Bolt Action Rifles
-
Gunsmithing 1-1/16 - 20 TPI 3A Thread spec sheet
Helpful link thank you. l had thought if tenon turned to major diameter of 1.0625 it would be unlikely to fit the action, looks like its going to be best to measure it vs going minimum spec. I appreciate you posting the thread calc link.- AZHUNTER
- Post #4
- Forum: The Armory
-
Gunwerks Onboard With SH
Nice! and they have some great prices in their "outlet" I just recieve a barrel blank for my first build from them.- AZHUNTER
- Post #3
- Forum: The Hide Deal Depot
-
Gunsmithing 1-1/16 - 20 TPI 3A Thread spec sheet
Anyone have a thread spec sheet for 1-1/16 - 20 TPI 3A threads, I will be attempting to thread/chamber a shouldered barrel for my Bighorn Arms Origin. The origin is advertised as using savage small shank threads and from what I have found the barrel tenon is usually turned to 1.055+ on...- AZHUNTER
- Thread
- Replies: 4
- Forum: The Armory
-
Gunsmithing Recommendations for action wrench to remove factory barrels...
TIP. put some grease or anti seize on the studs of your barrel vise or you might regret it.- AZHUNTER
- Post #13
- Forum: The Armory
-
Gunsmithing Recommendations for action wrench to remove factory barrels...
I have removed a few factory barrels with the viper vise and a surgeon action wrench. You can add a LITTLE heat (ie DONT use your acetylene torch and get red hot!) plumbers propane torch works fine, i read somewhere to heat till you see compound smoke and liquify in the scope base hole but dont...- AZHUNTER
- Post #12
- Forum: The Armory
-
Suppressors I launched my suppressor down range. Dogh!
I have a Silencerco omega and shoot it on several different calibers some direct thread and some with the ASR mount. After shooting both mount options I am leaning toward direct thread simply because of the shorter length overall. I just dont see how you could possibly launch one of these cans...- AZHUNTER
- Post #42
- Forum: The Armory
-
Gunsmithing What is the best way to recrown a barrel?
To answer your ?, probably a lathe after the bore of the barrel as been set to run true. Having said that I have a remington 700 222 60's era that I picked up for a good deal, I went to the range and it would not print better than 2" @ 100yd, after a closer inspection i noticed there was...- AZHUNTER
- Post #18
- Forum: The Armory
