• Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    Drop it in the replies for the chance to win a free shirt!

    Join the contest

Recent content by insight3b

  1. insight3b

    Gunsmithing M1A stock refinishing question

    What he said and to add: boyd's stocks are great but usually require inletting from the liner to op-rod guide for mags to seat fully and ensure proper functioning
  2. insight3b

    Gunsmithing Barrel crooked on bell and carlson stock

    Should have straightened the recoil lug before bedding...second photo shows out of alignment recoil lug although it would be easier to see looking from the rear of the action...like my photo
  3. insight3b

    Gunsmithing Barrel crooked on bell and carlson stock

    Your recoil lug isn't straight. I've had the same problem. Here's a recoil lug that isn't straight: The recoil lug isn't straight and fitting flush in the recoil lug recess of the stock instead the barreled action is resting on a 'point' of the recoil lug.
  4. insight3b

    Midway has a bunch of blemished bullets in stock

    Thought I'd pass this along. I've been using various blems for years and they are great: http://www.midwayusa.com/find?usersearchquery=blemished&itemsperpage=96&searchscope=all
  5. insight3b

    Mixing Once Fired Brass With X Amount Fired Brass

    I don't use new brass as all my rifles have favored/prove accurate with 1X fired LC. I used to track each piece but found it unnecessary and for the past few years I just load and shoot...have become a lot better at inspection of fired cases too
  6. insight3b

    Gunsmithing Cartridge quality for barrel break-in

    In a new barrel/new rifle I use once fired LC MG cases with a start charge of the powder I have the least of with the cheapest bullets I have on hand. I use it to get on paper and break in but its more important to me to have the brass for the next trip when accuracy testing actually begins...
  7. insight3b

    Rifle Scopes BDC turrets....Like 'em, or hate 'em?

    I like them for the simplicity and speed they provide when firing at more challenging unspecified distances. For my scopes without them and boringly firing from the defined 600yd line, 500yd line, 400yd line...I just use High-power established MOA come ups converted to scopes 1/8 or 1/4...
  8. insight3b

    So i finally got my .223 modified case for my hornady OAL gauge and........

    I just load my ammo for my AR pattern rifles to mag length...an AR is useless to me if I can't load the ammo into magazines. If I want the fattest part of the ogive closer to the lands I trim the meplat. My OAL tool is a stoney point which Hornady bought out and re-branded but both the .223 and...
  9. insight3b

    First time use of Hornady O.A.L. Gauge Questions??

    I use one as well and what I do is point the muzzle straight up I usually prop the rifle in a corner and insert the tool and slide until the bullets gets stuck in the lands. Not stuck hard enough that I need to knock it out through the barrel though. Stuck enough that a tap on the stock with my...
  10. insight3b

    Gunsmithing Why do you need to true the bolt face?

    By all means get some cerrosafe and post the results of your chamber cast and the dimensions of your fired brass then come back and call me a tard until then your words have no meaning
  11. insight3b

    Gunsmithing Why do you need to true the bolt face?

    Might need to cerrosafe your chamber and measure the casting then bump the shoulders back on your brass before you gall the lugs Cerrosafe Chamber Casting Alloy 1/2 lb
  12. insight3b

    .308 175 gr sierra matchking with imr 4895

    41.7gr in LC brass and CCI 200 has worked for me
  13. insight3b

    Gunsmithing Why do you need to true the bolt face?

    Even in fire-formed and neck sized brass there is still several thousandths clearance entirely around the cartridge. The brass expands to chamber dimensions when fired due to heat but when it cools it contracts as that is the only way it can be extracted
  14. insight3b

    Shooters Pro Shop has Nosler 308 168gr Match Blemished ammo $24/20

    Nosler Match Grade Ammunition 308 Win 168 Grain Custom Competition (Blem) 20ct
  15. insight3b

    Gunsmithing Why do you need to true the bolt face?

    Well we know it will cant at least two thousandths. Ammunition needs at a minimum two thou clearance all the way around in order to chamber. Before someone adds that they only neck size yadda yadda let's remember that brass expands to chamber dimensions only briefly then contracts several thou...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts