Recent content by wirehand

  1. wirehand

    Wanted: Brass Annealing Times

    Your best bet IMHO is to get the right temperature Templaq. Almost every ones times will differ because flame temps will vary from types of torches, the torch setting and gas left in the tank. Have you read Ken Light's article on 6mmbr?
  2. wirehand

    RL 550B setup for 308 , 45acp and 40 S&W free to a good home!!! AZ Local Only

    Also make sure the plastic tips on the primer feed tubes are pushed on all the way. If there is a gap between the aluminum tube and the plastic deal, the primer will turn slightly and not fall correctly. The primer feed tubes have a location rib on the plastic tip, turn the tube until it drops...
  3. wirehand

    Sidearms & Scatterguns Why you DON'T like Glock.

    I don't like Glocks because my time doing malfunction drills are pointless. BTW,I shoot Glocks.
  4. wirehand

    Groups go to CRAP after trimming brass

    Did you introduce the ultra sonic cleaner before the lousy group brass? The ability of the ultra sonic cleaner to get all the carbon residue from the inside of the necks could lead to a change in neck tension.
  5. wirehand

    Rifle Scopes mil dot reticle moa turrets

    Use a ballistic program that can give your adjustments in MOA form, such as Knights Armament Bulletflight. In that particular program just turn off Mrad display and metric scope setup.
  6. wirehand

    Night Vision Pvs 15 thermal overlay

    Right outta the box Huh.
  7. wirehand

    Suppressors E-File suppressor as individual?

    I don't belive so, as the way to upload finger prints doesn't seem to exist. The hard part might be finding a dealer that is willling to do the eform submissions. They have to register and do something with inventory I believe. Since the eform system has been so buggy, I think most are...
  8. wirehand

    Suppressors eform users?

    Thanks Bob, Thats pretty much what I ended up doing. All my documents were in a JPEG form after scanning and resizing, so after downloading an Adobe free trial I was able to create a couple of pdf's with the Declaration, Certification, Sch. A and cert. of compl. just for the hell of it...
  9. wirehand

    Suppressors eform users?

    When uploading the trust attachments, how can you get more than 10 and the 3mb limit by splitting them into "packages"? The newsletter mentions this method but doesn't elaborate how. It's probably something easy, but I am pretty thick headed. Also what does it take to withdraw a...
  10. wirehand

    Maggie’s Motivational Pic Thread v2.0 - - New Rules - See Post #1

    <iframe width="640" height="360" src="//" frameborder="0" allowfullscreen></iframe>
  11. wirehand

    RCBS 3 way carbide cutter?

    They also have the same thread as these Redding micrometer trimmers. Model 2400 Match Precision Case Trimming Lathe | Redding Reloading Equipment: reloading equipment for rifles, handguns, pistols, revolvers and SAECO bullet casting equipment
  12. wirehand

    Sidearms & Scatterguns my 460 Rowland experiment on a Glock 21 **PICS UP**RANGE REPORT**

    Very nice, Pretty much the top of the game for Glock conversions. I am very interested in how this plays out for you. After reading a little about the .40 super stuff, I had to aquire a 21sf and get that started. Like you, a 6in. barrel and solid top 21T slide is on the way. Man, I can't wait
  13. wirehand

    Suppressors First shots with 30BA - thoughts and a question

    It's also going to depend on what barrel contour and if shooting hand loads. The longer and skinnier the barrel the more possibility for shift. Adding weight to the end of a barrel will change the frequency to which it vibrates at, thusly changing the accuracy node possibly.