• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Search results

Search the forum Search Articles
  1. D

    New Lapua 308 palma brass.

    Re: New Lapua 308 palma brass. Remington URBR brass is my only choice for the 308/7.62 NATO family of cartridges. I use the URBR brass to form 22-250,243,260,7mm-08,308 & 358 brass. URBR small primer pocket brass weighs 155gr. .0105" neck wall .080" flash hole 30-35 reloads aren't uncommon...
  2. D

    Gunsmithing Rem700 bolt question for you who KNOW. *UPDATES*

    Re: Breaking cross pins... Should be a gap here......? A simple assembly with a total of 5 parts w/1 part that fractures is not Rocket Science 101. One should test inferior aftermarket pieces/parts on their own weapon systems prior to painting said parts & sending them out the door.
  3. D

    Gunsmithing Rem700 bolt question for you who KNOW. *UPDATES*

    Re: Breaking cross pins... Should be a gap here......? 3/32" drill rod was suggested a couple days ago by myself to cure the brittle dowel pin problem. Schools still in cession!
  4. D

    Gunsmithing Rem700 bolt question for you who KNOW. *UPDATES*

    Re: Breaking cross pins... Should be a gap here......? p.m. inbound
  5. D

    Gunsmithing Adjustable Comb M1A

    Re: Adjustable Comb M1A 1125-p.m. inbound makes no difference to me,but if you don't fill out your profile,the insecure will climb all over you.
  6. D

    Suppressors Good double action pistol

    Re: Good double action pistol DAO isn't my first choice,unless its a boot/back up piece. Traditional DA/SA is my choice. A slide gun manufactured by S&W for feed/function in 10mmAuto is my carry gun choice. A Sig 226/229/220 are my second choice of manufacturer. Any of the combat tupperware...
  7. D

    Gunsmithing Remington 700 bolt handle"JUMP"??

    Re: Remington 700 bolt handle"JUMP"?? No,just stating a FACT. After you've properly timed several thousand more bolts/handles/firing pins let me know!! Some prefer to BS customers into believing a TACtiCOOL bolt knob & a lighter/heavier sprung firing pin is the cure all. Wrong. PM's answered.
  8. D

    Gunsmithing Remington 700 bolt handle"JUMP"??

    Re: Remington 700 bolt handle"JUMP"?? B.S. Not even a politically correct guess... Bolt Timing Issues. Bolt Handle is improperly located on bolt body allowing firing pin striker to hit aft end of bolt body upon pin release.
  9. D

    Gunsmithing AR-30 breech diameter

    Re: AR-30 breech diameter Measure the barrel diameter,fwd of the receiver.
  10. D

    Gunsmithing Idea for bolt handle wrench.

    Re: Idea for bolt handle wrench. EDM the 1/4" female hex into the handle/knob. Interchangeability is key!!! (allen/torx/tamper proof) Been there.
  11. D

    Gunsmithing Trigger Suggestions Needed

    Re: Trigger Suggestions Needed 3 removal & replacements- WOW!!!! Clean/hone/adj/seal the OEM Rem std/pre 2006 trigger group & TIME the firing pin for the most consistent break. Otherwise depending on how you close the bolt "smartly" as per the operators manual, trigger pull will vary over 3/4Lb.
  12. D

    McMillan Prone stock opinions

    Re: McMillan Prone stock opinions www.robertsoncomposites.com
  13. D

    resizing the bmg

    Re: resizing the bmg Try some Imperial Sizing Die Wax to f/l size 50 cases. Redding produces Imperial w/ green dye in the mix currently. What diameter are these Lee 50BMG dies that you mentioned, 1-1/4" diameter??????
  14. D

    Gunsmithing bolt weld..

    Re: bolt weld.. May I suggest- If GA Precision wants you to build up the aft end of the bolt handle to lesson the clearance between shroud & body- Do it prior to attaching the handle to the bolt body. For added strength is BS. 3 each TIG tack welds are stronger than an improperly silver...
  15. D

    Gunsmithing bolt weld..

    Re: bolt weld.. The purge process also needs to be sought.
  16. D

    Gunsmithing bolt weld..

    Re: bolt weld.. Someone needs to practice on their own!!!!! A lathe is not required if done correctly. Someone came to the conclusion that the screw adornments were/are an abortion.
  17. D

    .308 Brass, best of the commonly found types?

    Re: .308 Brass, best of the commonly found types? Remington URBR brass.
  18. D

    remington 660 .243win

    Re: remington 660 .243win contact- Willie Manning Coquille Valley Machine Works Mrytle Point,OR. 541-396-6246 [email protected] 600/660 trigger guards CNC'd black anodized aluminum $75.00 + S&H.
  19. D

    Gunsmithing What grade of titanium for an action

    Re: What grade of titanium for an action Purchase a 700Ti rifle & part out the unused pieces. S&W did some nice work on the Ti actions.
  20. D

    Gunsmithing Nasty Carbon Ring

    Re: Nasty Carbon Ring Patch it with some Flitz. Then bore scope it for clarification.
Top Bottom
Back
Home
Forums
Merch
Alerts