Search results

Search the forum Search Articles
  1. Insayn

    LE Snipers Using Semi-Auto

    Re: LE Snipers Using Semi-Auto We are a municipality of around 1.2 million plus. We are running 3 semi-auto .308's out of 8 now. The rest are AI AW .308's. I initially started on a .223 semi-auto and after it expired I transitioned to an AI. Now I'm back on a semi-auto .308 and all .223...
  2. Insayn

    Suppressors Gemtech Sig Mosquito Barrels

    Just FYI...Gemtech Sig Mosquito Barrels are back in stock. They are an all steel replacement for those thy want to convert their standard Mosquito to 1/2-28 threaded. http://www.gem-tech.com/store/pc/MOSQUITO-Threaded-Barrel-17p65.htm
  3. Insayn

    155gr lapua scenar loads?

    Re: 155gr lapua scenar loads? I'm also 0.020 off the lands. It is the furthest out I can get because of the HSP magazine.
  4. Insayn

    155gr lapua scenar loads?

    Re: 155gr lapua scenar loads? I get a slight crunch, not a lot. My OAL is 2.85 off the meplat. So far I haven't seen any pressure signs on the 60 cases I've tested of that load. I'll have another 30 to test and zero in tomorrow.
  5. Insayn

    155gr lapua scenar loads?

    Re: 155gr lapua scenar loads? I pretty much finished up my load build up for now. My rifle is a R700, Shilen Select Match 7HV, 24", 1:12. I am settling at: 48.1 grains Varget Federal 210M primers Hornady Match Brass 2.213 OAL off Ogive 155 Lapua Scenars 2961 fps Avgerage on a 51 degree...
  6. Insayn

    Feedback Good Guy List

    Re: Good Guy List Longeye is GTG.
  7. Insayn

    Gunsmithing Barrel Threading Method

    Re: Barrel Threading Method Thanks for the replies. Just comparing after seeing a lot of smiths photos here on how they did it compared to one I watched in person with the centre in the crown/muzzle.
  8. Insayn

    Gunsmithing Barrel Threading Method

    Is it appropriate to thread a barrel by chucking The chamber end in a lathe with the muzzle/crown in a centre? A lot of the photos and write ups I see here use a rod in the barrel to indicate center and chuck it close to the muzzle end and/or utilize a spider.
  9. Insayn

    Redding Type S match die set opinions

    Re: Redding Type S match die set opinions What is the difference between the Type S and the Competition set besides the dial?
  10. Insayn

    Suppressors Building your own suppressor

    Re: Building your own suppressor Try www.silencertalk.com They have a build your own section with designs and requirements.
  11. Insayn

    US SWAT Sniper Championship

    Re: US SWAT Sniper Championship I competed for the last 2 years. I ended up taking 6 IV's through the week last year (also competed in the SWAT Comp). It was tough physically in the heat, especially when in armor and being down there for both events drained me. They didn't really provide...
  12. Insayn

    Gunsmithing HS Precision Stock

    Re: HS Precision Stock I figured it was to dampen the sound or to suspend bits and pieces that rattle inside the stock. I ended up pulling a chunk of epoxy and cut piece of plastic from inside that I never would have heard previously. I pulled the foam and will just spray a squirt of "Good...
  13. Insayn

    Gunsmithing HS Precision Stock

    Re: HS Precision Stock My hole for the Grovtec is in the rear about 1.5" from the recoil pad in the center. I can visibly see inside and don't see any weights, just a hollow buttstock. I pulled it all out, but will probably just shove it back in prior to epoxying the Grovtec base.
  14. Insayn

    Gunsmithing HS Precision Stock

    Re: HS Precision Stock Secondary question. I installed Grovtecs in a HS Precision LTR stock without any problems. I am doing it on a second HS Precision stock and when I drilled into the buttstock I am finding a lot of white foam strips inside. What is the purpose of the foam strips?
  15. Insayn

    Feedback Good Guy List

    Re: Good Guy List Beretta989 xray9 Both GTG
  16. Insayn

    So I had a little down time...

    Re: So I had a little down time... I even had to wear it today on a call out today...wasn't expecting to dawn it so soon.
  17. Insayn

    So I had a little down time...

    GO STEELERS!!!
  18. Insayn

    Gunsmithing Getting a lathe ..... now what?

    Re: Getting a lathe ..... now what? Pacific Tool & Gauge? http://www.pacifictoolandgauge.com/index.htm
  19. Insayn

    identify this

    Re: identify this If you look around it was something Sig offered. I sold one last year like that.
  20. Insayn

    Rifle Scopes LE Optic Question

    Re: LE Optic Question Having gone through a lot of schools as well as instructing a few you will see anything and everything in the LEO arena. It is a large spectrum you are looking at from full time teams to part time regional teams. We are a tier 1 team with a decent budget and procure...
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts