Search results

Search the forum Search Articles
  1. usmc7980

    Gunsmithing Make your own Remmy 700 Firing pin tool

    Re: Make your own Remmy 700 Firing pin tool Took USHandgunners suggestion and made a new and improved version. I'm going to make a real nice one at work in the morning that is the same concept as this one. I'm going to move the holes up some and put a support between the two angles for the...
  2. usmc7980

    Gunsmithing Make your own Remmy 700 Firing pin tool

    Re: Make your own Remmy 700 Firing pin tool well the 1/8" angle turned out to not be strong enough so I made a new one with 4x4x1/4" 6061 T6 angle. Mom just got here so I'll get pictures later
  3. usmc7980

    Suppressors New holster for my 1911

    Re: New holster for my 1911 The mouth is reinforced, so no it does not crush down when I unholster the gun. I can easily reholster with one hand
  4. usmc7980

    Suppressors New holster for my 1911

    Re: New holster for my 1911 It is shark and leather riverguide, as far as the presentation it was sticky the first day or so then it got alot better. Just needed to go in and out a few times. Now it is super smooth and still retains nice and tight. I'v e always been a kydex/leather hybrid...
  5. usmc7980

    Rifle Scopes Complications with my SIMRAD cap?

    Re: Complications with my SIMRAD cap? That looks like them but they were sold a s Badger rings not SPA
  6. usmc7980

    Gunsmithing Make your own Remmy 700 Firing pin tool

    Re: Make your own Remmy 700 Firing pin tool I may just do that, if I drill it deeper to rest on the shoulder it will take the pressure of the tip of the firing pin tip when compressing the spring. That said I did not notice any negative affect on the pin tip
  7. usmc7980

    Rifle Scopes Complications with my SIMRAD cap?

    Re: Complications with my SIMRAD cap? I may be wrong and I'm not bashing the seller but that damn sure does not look like any BO ring cap. The cap currently on the BO site has a notch on it. All of the ones seen look like this picture of a BO cap mounted. Notice the screw holes, tue USMC BO...
  8. usmc7980

    Gunsmithing Make your own Remmy 700 Firing pin tool

    Re: Make your own Remmy 700 Firing pin tool Thanks, I like to jerry rig, and it's always good when it works when I'm done
  9. usmc7980

    Bell & Carlson A3 Hook Style Tactical Medalist

    Re: Bell & Carlson A3 Hook Style Tactical Medalist Lonewolf beat me to the punch
  10. usmc7980

    Bell & Carlson A3 Hook Style Tactical Medalist

    Re: Bell & Carlson A3 Hook Style Tactical Medalist That stock is not inherently bad just because it doesn't have flush cups. If you are in the field operating, yes you would want a Manners or McMillan or some $400-700 dollar stock that a tank could drive over and it will sill function. If...
  11. usmc7980

    Rifle Scopes 1 in hunting glass

    Re: 1 in hunting glass The Fullfield II's are not bad scopes, I have 2 on hunting rifles myself. For lowlight and knob turning I would try the new Monarch X and the Zeiss's are always a good bet. It will be a compromise for a hunting scope with target knobs.
  12. usmc7980

    Gunsmithing B&C Medalist stock repair necessary?

    Re: B&C Medalist stock repair necessary? I would only worry about it if the nick/ crack is in the in-letting for the action /magazine/trigger guard area
  13. usmc7980

    Suppressors New holster for my 1911

    Re: New holster for my 1911 I think it is extra for the exotic trim but not much only like $5
  14. usmc7980

    Suppressors New holster for my 1911

    Re: New holster for my 1911 Show me one leather holster maker that hasn't copied designs from others and I'll be impressed, there are only so many ways to make holsters. At some point the designs all overlap I paid $45 for this one, but we had a trade too. They normally go for $70
  15. usmc7980

    Gunsmithing Make your own Remmy 700 Firing pin tool

    Final fixture here, It is made of 1/4" 6061 T6 flat plate with angle bolted to it. Everything else was trial and error junk I made my own because I'm a cheap ass. It's really simple, I used two pieces of 2"x4"x1/8" aluminum angle from my shop, some scrap wood, and a piece of 1/2"...
    • usmc7980
    • Thread
    • 700 firing make pin remmy tool
    • Replies: 35
    • Forum: The Armory
  16. usmc7980

    Gunsmithing SPS TAC transformation

    Re: Did my bolt knob I found a new goody I want to try. It is an octagonal bolt shroud, it will serve no purpose other than looks. It is like the one on Surgeon actions, but I want to check out the guy who makes them, any body have input? Here's a link to the site...
  17. usmc7980

    Rifle Scopes Complications with my SIMRAD cap?

    Re: Complications with my SIMRAD cap? You have a 30mm or 1" scope tube. If it is a 1" tube there is a spacer that goes in the ring to take up the gap you are talking about. Pictures always hep, just post them by default
  18. usmc7980

    Suppressors New holster for my 1911

    Re: New holster for my 1911
  19. usmc7980

    Suppressors New holster for my 1911

    Got a new CCW holster for my 1911 from Little Bear holsters in Jacksonville FL. The retention is great, it is really comfortable and it looks bad ass to boot
  20. usmc7980

    Gunsmithing Dimensions of scope base?

    Re: Dimensions of scope base? way over my head
Top Bottom
Back
Home
Forums
Merch
Alerts