Search results

Search the forum Search Articles
  1. bptactical

    Gunsmithing REM 870 ejector replacement

    Reusing the old rivet is hit or miss. Sometimes you have enough, sometimes you dont.
  2. bptactical

    Gunsmithing Ring gauges

    Why bother, they are damn expensive and will wear out eventually. Just buy a good thread micrometer instead.
  3. bptactical

    Gunsmithing Applying proper Torque with a Strap Wrench

    Take a strip of emery cloth long enough to go around the nut twice. Fold it in half backwards, abrasive side out. Wrap that around the nut and then apply your strap wrench and snug the nut down. 40 ft/lbs is your starting torque and then just enough additional torque to line up for the gas tube...
  4. bptactical

    Gunsmithing Which Product Works Best to Remove Copper Fouling?

    I have had good luck with Tetra copper remover.
  5. bptactical

    Gunsmithing You'll Shoot Your Eye Out. . . .

    "Rooster Dixon"??? Has a ring to it.....
  6. bptactical

    Gunsmithing Any 'smiths with Weatherby Mark 5 experience?

    I have done a few rifles with pressure point bedding. PITA and if somebody knows of a quicker way I am all ears. With this being an older rifle stock compressibility is definitely a concern and I think your logic is sound. I would note the amount of pressure on the barrel, remove the pressure...
  7. bptactical

    Gunsmithing You'll Shoot Your Eye Out. . . .

    Get well soon and thankful it wasn't worse. Having had eye injuries before I feel your pain. (a slap shot to the eye area from 30' by a former NHL player will put a hurt on you)
  8. bptactical

    Gunsmithing blown up tikka

    Oohh that left a bruise!
  9. bptactical

    Gunsmithing alternative to trustrip for prepping barrel

    Acetone works just fine but blasting is the best prep.
  10. bptactical

    Gunsmithing Grizzly Gunsmith D1-5 Back Plate

    Yup! I just took a D1-4 adapter plate, turned down the OD to match the spindle diameter and drilled/tapped it every 90 degrees. I got the backplate from Blue Ball machine for $25.00 used. One of the holes interfered with the cam pin, just trimmed the pin a smidge and it works fine. The really...
  11. bptactical

    Gunsmithing muzzle thread ?

    9/16 x 24 is a good option for slimmer profiles.
  12. bptactical

    Gunsmithing Finally!!

    You guys get nervous about that? Wait until you sink a counter bore for a sling swivel in a $30K Chapuis double rifle. That'll give you some pucker.
  13. bptactical

    Gunsmithing chambering with a collet chuck?

    While your collet may have near zero runout the barrel may very well not. What the OD is doing is irrelevant. Use the 4 jaw gimble ring setup described above.
  14. bptactical

    Gunsmithing Thread Adapters

    If I need them, I make my own.
  15. bptactical

    Gunsmithing Level action to stock in glass bedding?

    I always made sure my barrel was where I wanted it then adjust accordingly on the receiver end if need be. Never had one so far off of level it would be an issue.
  16. bptactical

    Attack On The Grid...

    Or just a bunch of stupid hood rats playing wit dey choppas... Maybe it's just me but I don't get many requests for precision rifles chambered in 7.62 x 39.. Doesn't pass the smell test
  17. bptactical

    A Glimmer Of Hope For CA

    You mean the same SCOTUS we were sure would smoke O-care right?
  18. bptactical

    Hope for Connecticut

    Read up on Mike Lawlor. Dyed in the wool full blown communist.
  19. bptactical

    Gunsmithing A quick thanks to you all

    Just know when something is beyond your skill set. And I agree, there are some incredibly talented folks here and their willingness to share information is exemplary.
  20. bptactical

    Gunsmithing A Real Gunsmith Question

    Jeff Beck, Robin Trower, SRV. But if I am doing something that really requires concentration I usually turn the tune off. I want to hear what my machine is doing.
Top Bottom
Back
Home
Forums
Merch
Alerts