Search results

Search the forum Search Articles
  1. Hateca

    Gunsmithing Threading the muzzle for sup...

    Re: Threading the muzzle for sup... In short no.
  2. Hateca

    Stiff extractor on a 223 Remington?

    Re: Stiff extractor on a 223 Remington? This is a common issue with the .223. Not sure which it is the extractor or bolt but I believe the extractor grove in the bolt nose wasn't cut deep enough for the snap in extractor to have enough spring to it. Most will fix this by Dremeling off the...
  3. Hateca

    Rem 700 5R .223 barrel dimension

    Re: Rem 700 5R .223 barrel dimension .830" to .840"
  4. Hateca

    Gunsmithing texturing your stock

    Re: texturing your stock <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: mk443</div><div class="ubbcode-body">I know I've read threads on here before about texturing your own stocks and I had a few unanswered questions. I read a couple forums about people using a...
  5. Hateca

    Gunsmithing what do you use to tighten barrel

    Re: what do you use to tighten barrel Or use an inline wrench and a Badger lug alignment tool.
  6. Hateca

    Gunsmithing Jewell hitting inside of McM A5?

    Re: Jewell hitting inside of McM A5? I wouldn't say common but it does happen and if you are using a Badger DM chances are it's hitting that as well.
  7. Hateca

    Gunsmithing 300 wm chambering ??

    Re: 300 wm chambering ?? You don't, not two barrels or chambers are the same. And even if you did after a few hindered rounds the throat going erode to move anyway.
  8. Hateca

    Gunsmithing Bottom Metal in a 700 BDL

    Re: Bottom Metal in a 700 BDL For factory BDL to mag your options are Wyatt and H&S but both of those use a proprietary mag.
  9. Hateca

    Gunsmithing converting AICS mags for 6mmbr feeding

    Re: converting AICS mags for 6mmbr feeding <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: oldreliable45120</div><div class="ubbcode-body">I have that article already. Didn't go into too much info on mag work. I have a 1-14 twist and shoot 68 grainers and have a...
  10. Hateca

    whats the difference between mcm a5 and a a3-5

    Re: whats the difference between mcm a5 and a a3-5 A3-5
  11. Hateca

    Cerakote

    Re: Cerakote
  12. Hateca

    Gunsmithing Cerakoting Tac 30 bolt

    Re: Cerakoting Tac 30 bolt <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ccLdvc</div><div class="ubbcode-body">Would it be possible to just OD green cerakote the shroud and handle and leave the body alone? I could live with that! </div></div> Yes this is...
  13. Hateca

    Gunsmithing AI magazines and other actions . . .

    Re: AI magazines and other actions . . . Plus that's a single stack magnum mag not a wider AICS .308 or AW mag which would require more then described and doing anything to those mags will get you no where. Magnums and non-magnum AICS mags is apples and oranges.
  14. Hateca

    Anybody have any trouble with AICS magazines

    Re: Anybody have any trouble with AICS magazines Double check and be sure the bullet tip is not getting caught up on the underside of the feed ramp. The feed ramp could be extended into the mag area slightly. This would have nothing to do with the mag but the placement of the bottom metal...
  15. Hateca

    Surgeon wsm and AW mag?

    Re: Surgeon wsm and AW mag? http://www.snipershide.com/forum/ubbthre...604#Post2361604
  16. Hateca

    Gunsmithing Surgeon RSR - mill to accept AW mags?

    Re: Surgeon RSR - mill to accept AW mags? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: KPK</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: HateCA</div><div class="ubbcode-body"><div...
  17. Hateca

    Gunsmithing Surgeon RSR - mill to accept AW mags?

    Re: Surgeon RSR - mill to accept AW mags? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: KPK</div><div class="ubbcode-body">Jared, what do you got? Thanks for the info. So I take it any good gunsmith can get this done rather easily? I haven't collected all my...
  18. Hateca

    Gunsmithing Cerakoting Tac 30 bolt

    Re: Cerakoting Tac 30 bolt <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ccLdvc</div><div class="ubbcode-body">Going to have my Stiller Tac 30 barreled action painted, should I paint the bolt and inside the action or are the tolerances too tight on these...
  19. Hateca

    Gunsmithing Surgeon RSR - mill to accept AW mags?

    Re: Surgeon RSR - mill to accept AW mags? Yes it can be done but don't do it unless you know exactly what you are doing or you'll end up with an expensive paperweight. This is their tactical action that I did for a guy in .243 And this is a Remington. There is no difference in the RSR...
  20. Hateca

    Gunsmithing Sendero bbl action not lining up in McM channel

    Re: Sendero bbl action not lining up in McM channel Common with Remington barrels. 1. Either the recoil lug is rotated slightly causing it to push on the stock causing the barreled action to push left. 2. The barrel has lots of run-out and isn't time correctly (Remington doesn’t time...
Top Bottom
Back
Home
Forums
Merch
Alerts