Search results

Search the forum Search Articles
  1. p5200

    CZ 10 Round mag Question for CZ 457 feeding into Lilja barrel on 1st round only!

    I ordered one off Ebay. With the Eley Match all 10 rounds chambered fine. The 1st round of SK Rifle Match hangs up every time and doesn't go in the chamber. Anyone else have this problem with the 10 round mags using certain ammo brands? Thought, maybe after some use it might clear up after...
  2. p5200

    Cleaning the leade area only per Lilja instructions question

    My guess is to follow their directions, you'd have to use a cleaning loop because a jag would allow patch to fall off correct? Their instructions are, (We suggest cleaning in the following manner. After approximately 100 rounds push a dry loose patch through the barrel from the breach end. This...
  3. p5200

    What kind of cleaning rod to use on a 22LR Lilja barrel Stainless

    I'm looking for a decent cleaning rod to clean a Stainless 22LR Lilja barrel, chamber and lead. Just something I can safely clean without worry of harming the bore / chamber. This is a CZ 457 and I have a bore guide for it. Thanks!
  4. p5200

    Method relieving stock barrel channel for larger diameter barrel Questions

    I'm going to install a Lilja 1.00" barrel in a CZ 457 Standard Varmint stock. My question is, do I start at the bottom of the channel with smaller socket/ sandpaper? Or, start at top of channel with final width of socket and sand paper needed. I just want to avoid the top finished edges from...
  5. p5200

    Lilja 1.00" barrel fit with CZ 457 Varmint with Warne Picatinny rail installed Question

    Should there be enough clearance at the front of the Picatinny rail for the 1.00" Lilja barrel? Thanks? (y)
  6. p5200

    Lilja 1.00" X 21" CZ 457 22LR barrel Question

    Hello everyone, Does anyone know if this barrel comes with a set of shims included? https://riflebarrels.com/shop/drop-in-barrels/cz-455/22-rf/cz-455-457-22lr-1-000-x-21/
  7. p5200

    L3i barrel o Lilja CZ 457 questions

    I've been looking around at aftermarket barrels. Trying to decide between L3i and the Lilja barrels. I won't be shooting match grade ammo all the time. From a little searching, it's been said the L3i barrels aren't as picky about ammo as the Lilja barrels. Does this sound about right or, was I...
  8. p5200

    Bedding a bergara bmr 22LR

    Hello, has anyone bedded a bergara bmr 22LR. There seems to be a lot of slop between the barreled action and the stock. Thanks for all input!
  9. p5200

    4-40x5/8 full dog set screws and drill and tap?

    I'm replacing factory trigger on a bergara bmr 22LR. Thought I would try the trigger mod lots have done. Not sure which tap to buy. Something that will be less likely to leave shavings inside the trigger. Suggestions needed on what tap, and where to order the 4-40x5/8 full dog set screws. Thanks!
  10. p5200

    Triggertech primary trigger for bergara bmr 22lr?

    I hope this trigger fits because I just ordered one! Thanks Remington 700 Primary Trigger // TriggerTech
  11. p5200

    bergara bmr steel 22lr action screw diameter and thread type?

    Anyone know what size/type threaded rod I woud need. I plan to bed it and that is cheaper than ordering long inletting screws. Thanks! :)
  12. p5200

    Weatherby Vanguard steel magazine followers?

    Does anyone know if there are any steel magazine followers for the Weatherby vanguard? I have to keep adding a bit of oil to the plastic one. It develops a heavy drag on the bolt when it gets dry. Or is there any mods that can be performed? Thanks!
  13. p5200

    Bedding question

    I'm getting ready to bed my Weatherby Vanguard. I'm sure I relieved too much material around the lug and rear tang. I will be using Marine Tex compound. With the compound being thick, will it cause me problems? Also, I've seen where a lot of folks remove barreled action after several hours. They...
  14. p5200

    removing Cosmoline from new rifle metal?

    Any suggestions on how to remove the brown preservative from my new Savage 110 tactical rifle? Thanks! :)
  15. p5200

    Mauser m18 6.5 Creedmoor base mount Question

    I've been told that Remington 700 long action bases would fit this gun can anyone tell me for sure, if this base will work before I order? Thanks...
  16. p5200

    Mauser m18 6.5 Creedmoor handload accuracy?

    Has anyone gotten one of these rifles to group really well and consistent using handloads? From what I've read, the best groups have been gotten only with match grade ammo and are very pickey. The reviews I've found state they don't produce the accuracy they have claimed. Thanks for any info! :)
  17. p5200

    Use of FrogLube question

    For those who use it, do you treat the bolt & lugs with it in the usual manner or, do you stick with Tetra Grease etc. for the locking lugs and any camming type surfaces? Thanks!
  18. p5200

    Zeiss Victory prf rangefinder sale

    I just bought one for $200.00 more this is a great price if anyone needs one 1300yd.. Zeiss Victory PRF Laser Rangefinder - 8X26 T PRF at MacksPW.com
  19. p5200

    Gunsmithing Aproximate cost to re barrel a Remington sps AAC .308 with a match grade barrel?

    I have replaced the factory stock with a B&C Medalist style A2 stock. I'd like to keep the same caliber but, replace barrel with a longer match grade and have action trued. Thanks for all input.
  20. p5200

    Gunsmithing eezox used as a lubricant?

    Would this be good to lubricate as well as a cleaner, and rust inhibitor? I've been using CLP and decided to order some eezox to try. Also, will it work on the slide of my M&P 40 or should a light coat of grease be used on the slide instead? All advice is appreciated!
Top Bottom
Back
Home
Forums
Merch
Alerts