• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. P

    Rifle Scopes Help needed for mounting Leupold MK AR scope

    I have a Leupold MK AR Scope, aluminum MK 4 Leupold rings and a Remington R-25. When I mounted my Leupold scope on my M24 I used 65 inch-pounds of torque to mount the rings to the rifle and 22 inch-pounds of torque to mount the top of the rings to the bottom half of the rings. I am unsure...
  2. P

    Best Trigger for AR-10

    Looking for an opinion on replacing the stock trigger on Remington R-25. I have been given a couple of recommendations - Timney AR-10 and AT Gold AR-10. Anyone have an opinion on which one would be the best buy? I am looking for a replacement trigger module to drop in without gunsmithing...
  3. P

    .308 Resizing problems

    Re: .308 Resizing problems I did take a look at these but I think they will work opposite of my problem. I am not getting hardly any setback and the ram is already overcamming 1/8 turn inward on the die. The Redding Shellholders are incrementally thicker than the .125 industry standard...
  4. P

    .308 Resizing problems

    Re: .308 Resizing problems Also, I forgot to mention - there is no expander ball in my die. I am using the .336 sizing insert for the neck so the expander ball was removed.
  5. P

    .308 Resizing problems

    Re: .308 Resizing problems Thanks for the reply. I thought it might be the bleed hole since the locking ring covers it up. I measured the location of the bleed hole and then drilled a hole in the locking ring to match it. Now, the hole is clear through the locking ring. Unfortunately, that...
  6. P

    .308 Resizing problems

    Re: .308 Resizing problems No, I am using Nosler Custom brass and this is the 3rd reloading for these.
  7. P

    .308 Resizing problems

    I only load .308 Win and am using RCBS Gold Medal Dies. I use a Full Length sizer with a .336 insert for the neck. Here is my problem. I start with clean, tumbled, fired cases that have had the primer already removed. I lube on the RCBS lube pad and resize. I am trying to only bump the...
  8. P

    M24 Barrel Questions

    Re: M24 Barrel Questions The rifle is still shooting extremely well. I had a couple of groups at .25 MOA. The rest between .5 and .75 MOA. The copper fouling are very vivid copper streaks in each groove from the edges and covers about half the groove with the center of the groove with any...
  9. P

    M24 Barrel Questions

    I recently received my M24 from Texas Brigade Armory and have a couple of questions. The barrel is supposed to be a Mike Rock 5R Stainless Steel. When I look into the receiver, where the barrel was machined for the .308 case, it is nice and shiny just like stainless steel. At the muzzle end...
  10. P

    Rifle Scopes Need Help Mounting Scope

    I should know but I don't so I will ask if it matters what sequence is used to mount a scope to the rifle. I have a Leupold Mark4 LR/T M3 to mount to my M24. It has a two piece Mark 4 rings and two piece base. The bases are already mounted but not the bottom portion of the rings. Leupold...
  11. P

    Need help with H&S Stock

    Re: Need help with H&S Stock Thanks for the help. You mention epoxy and JB Weld which is also an epoxy which you used. Are you saying you recommend the JB Weld epoxy or you would just use something else like a regular 5 min epoxy?
  12. P

    Need help with H&S Stock

    I bought a new H&S Synthetic stock with adjustable butt plate. It came with two swivel studs on the foregrip and a third near the buttplate. They are all very loose and if tightened up tight against the stock they are about 45 degrees beyond perpendicular to the stock centerline. They all appear...
Top Bottom
Back
Home
Forums
Merch
Alerts