Search results

The surface against which the safety lever is impinging coincides with that of the Rem 700. See pic below. Guard screw holes are used for alignment. I suppose we could bump it forward a bit but it would be nice if triggers advertised as R700 compatible were actually made that way. Ted

Now shipping As some of you have found out, we started shipping the Coup De Grâce. We're still not up to full speed but at least two hundred or so orders will be filled over the next few days. Please don't ask us when yours will ship because that will only cause delays for everyone. ARC team...

Barrel Interface Drawing Error Gratitude goes out to tstevens who brought an error to my attention. The calculation for the ball measurement should be 2.0217 - .2887 x DimA, and not 2.0217 + .2887 x DimA. I carelessly made the dreaded sign error. This is just another reason why I love the...

I might have been wrong about that. I'd really like both short and CIP long action double-stack AW-type mags for the .532 case head family. Does anyone make one? I was laying that out yesterday and it might work fine in this action. I did not find one on either the Mile High or the Accurate...

The CIP long action mag for the 338 Lapua/300 Norma family is different than that for the 300 WM family. Both mags will work in the long action Coup. Non-CIP lengths mags will probably work as well so long as your chassis or stock is designed for them. Our long action Xylo chassis is designed...

Magazine Compatibility for Long Action Coup De Grâce We have designed one variant of a long action receiver that works well with CIP length (3.85") single stack mags from Accuracy International and Accurate Mag. Example Accuracy International AICS 338 CIP...

Placing an order When placing an order, please hit the Pay Now button only once otherwise you will unintentionally place duplicate orders and that's not good for anyone. Thank you. Ted

Mag Latches The chassis in the video has the standard latch in it. Although I cannot speak to other chassis, I am guessing that their standard latches will work fine with the AW mags and will need to be adjusted or shortened by 0.065" for the AICS mags. Ted

Buy the Coup. The fact that it's optimized for use with the AI AW mag coupled with a highly evolved feature set really sets this thing apart. And at $900, all I can tell you is get in line. Ted

Bolt Handle Strength The Rem 700 handles were brazed onto the bolt bodies. Probably less than ideal. We actually use a heavy ball peen hammer to open the Coup's bolt after destructive tests. Sometime we can't open them but them but we have yet to break a handle while trying. We have also...

Grease We don't slather the actions with grease and never did. That said, grease is a good thing so long as it's used sparingly. It doesn't take much of it to reduce friction noticeably. I've yet to find to metallic surfaces, coated or uncoated, that didn't slide against one another more...

Came across this video recently. You guys might find it helpful. I liked it but I'm biased. Ted

It was supposed to be but we didn't get to it. Maybe tomorrow. We're screwing around with some editing software. Not sure why. An edited video from us would be a first. Ted

Uh, no. It's never that simple. Literally millions of actions using bolt lug channels were made before the advent of wire EDM. Broaching is still highly productive and effective. One need only to look at Tikka or Savage to know that lug channels can be produced at very low cost in high...

AIAW and AICS or equivalent mags will work. The AX mag will not work because of a lug that protrudes from its forward face. You can see the difference in the attached pictures. Ted

Noticed a typo in that. Just edited the web site to make the correction.

Test coupons are one thing. Actual test articles are another and absolutely essential. Ted

Not sure. The KRG Bravo video reveals a screw immediately behind the mag well which may interfere with the trigger hanger. If it does, an easy mod might be able to make it fit. Need to get one in here. I hope it works. That would make for a great build at a phenomenal price. Ted

That cases was intentionally cut to ensure that the case would not contain pressure. Our aim was to pressurize the receiver in order to see if it would blow apart. We're testing the mechanical properties of the receiver during these tests, its metallurgy essentially. Ted

Might work. The rifle in the Vudoo both at Shot Show had a short action CDG with Hawkins bottom metal. Some material removal was necessary near the back end of the mag box because of an interference with the trigger hangers. We just need to make Andy aware of this and he'll have to decide...