Search results

I am handicapped and am planning a hunt in New Mexico, so I want to have a walking stick, that I can also shoot off of. I have a couple of the Primos trigger sticks, but they specifically state that they are not to be used as walking sticks, plus one of my two, occasionally 'collapses' on it's...

From what I can tell you have to have a pic rail to mount the Atlas bipod to your rifle. I was just curious if there is any way to mount it to a 'regular' rifle that has a sling swivel stud like you can with a Harris. If there isn't I hereby advise Kasey to figure out a way, there are a lot of...

I'm looking for recommendations on good quality empty chamber indicators. I've looked on Midway USA and didn't see any that I thought were good. Looking for suggestions, recommendations.

I am looking for input from those who know, what is involved with re-chambering a 30-06 barrel to 300 Norma.

I have happened into a takeoff 30-06 barrel-unused-and wanted to know about the ability of re-chambering it to 300 WSM? Thanks for any feed back.

I am trying to garner load data for 150 gr. TSX's in 300 WSM, I can't get connected to the Barnes website, so any assistance would be appreciated.

I had a bad experience in the hospital that has left me without any feeling in my feet. This causes me to have to wear braces at all times so putting on a traditional boot, that goes 1/2 way up my calf is no longer possible. I am looking for input on a pair of low top 'Hiker' style boots or...

I have a nephew that has a .223 KelTec and he wants to thread the barrel for a flash supressor. My question is is it a reasonable endeavor to hand thread 1/2x28 1/2" long of the barrel by a hand die? I have a lot of experience with taps and dies up to 1/2x18 on 4140 but never have done anything...

I've been looking for this thread and although usually pretty good at searching for stuff, can't find this thread at all. My searches generated a bunch of useless stuff.

I have a few rigs that are not very 'mission critical' to my needs and I am looking to put some glass on them at about the $500 range. Typically don't limit the budget quite that much, and I would prefer a scope with a fast focus eyepiece. Tried a Burris Fullfield II and was disappointed...

I am ordering a new bolt from PTG for an old Rem model 721. I am looking for advice/opinions on whether to order a Rem or Sako extractor and why. I am not a smith of any level, and want to order the bolt with the extractor installed. <span style="color: #33CC00"> Well my bolt came in, and it...

Just installed this barrel on my 10/22, had to relieve the barrel channel a bit, that went well, but put her all together and it won't exract now. It appears that the extractor can't get beneath the rim of the cases, the come out pretty easy with a small flat blade screwdrive to start them. It...

Am trying to decide between two 'midweight' contour barrels, the Shilen or the Clark. The Clark is a little over $100 less than the Shilen, both have excellent reviews. I have actually ordered both, and my friend will get whichever one I don't run. Looking for experienced users opinions and...

I am trying to decide between 3 annealing machines, the ones that I have currently narrowed down to are: 1. Bench Source 2. Ballistic Edge 3. Ken Light 100 ( at bottom of page) I am looking for feedback and info, especially from owners of these machines. I am interested in how...

The safety on my CZ 453 is VERY stiff. I have about 250 rounds through it so far, and it is very accurate, but the safety is just a bear to put on and take off. I tried a very small amount of sanding with some 600 grit emory cloth on the corners of the safety catch, but can notice no difference...

Well, I have gone a long time reloading and never gotten into annealing. I have been researching the various MO's out there, and being in a cash crunch for a while, I decided to start with the Hornady annealing kit. It is simply 3 holders that are basically 1/4" shanks attached to what amounts...

I have been looking for a 'regular' (non-threaded) barrel in a contour a little heavier than a factory, wihout sights on it, but without going all the way to a .920 contour. Looking for a barrel that is in stock somewhere, not wanting to wait for a Lilja/Krieger etc. Appreciate any leads...

Trying to discern what the thread size is for the screw on the Ruger 10/22. Also, anybody pillar bed the 10/22? I have seen mention of it, just trying to figure how, do you cut a tube just slightly longer than the amount needed to clear the fore-end and tighten down against the receiver?

I am interested in putting a new bolt knob on my CZ 453, I can't find any relevant intel doing a search here... Anjyone know of any DIY options, would like to NOT have to send my bolt to someone to have it done if possible. Thanks for any ideas/input

Does anybody know if a Rimfire Technologies mag release will work on a Kid trigger group? I am leaning toward the Kid trigger group and bolt handle + their receiver pin kit, but really like the idea of the 'pull' style mag release from RF... wish Kid made a factory contour barrel