Search results

I see your attachment. That other one that Bobalos had a picture of looked like it may have hooked out to the rifle itself? I can see if you had a big enough fishing net that can curve up and over the akm while on the bench would work too for sure. I want to either get one that will hook onto...

Do you have any pictures of what you made? $65 is not bad too for sure. I tried last night to look up for a brass catcher that looked like it, but I didn't find an actual location to buy it.

Soccer goal is pretty funny too. It works although it is funny looking for sure. I don't reload for the Akm yet, but for my Ar I sure do. If that can't keep my brass close by so i can collect it, I'll take ugly lol. I went on a prairie dog hunt last year and it was a blast, it was set up to...

This is for the bench only. It works great actually, my wife didn't have any issues with getting burned at all. It actually pretty big, 3 feet long 30 inches wide and tall. Cost $35

Wow that's crazy 200? I made a little video 40 seconds for a friend. But I couldn't upload it here. It works for sure. With the akm47, the brass still bounces but not bad at all. I found all 30 today. They either landed either of 3 ways. About 5 feet straight ahead, on the table or...

Home made nothing is glued yet until I take it out to test it. I can make remove a upright so that it has only 3 supports and it is strong enough and stable too. The cardboard roll is basically how you would be with a rifle. Fire the rifle and the brass will land on the table

Hi I bought one of these in the late 1980 and a few months ago, I bought the latest one. I have been going over it and came to a section that makes me think. I know if the brass stops growing (after resizing) then it is time to toss it. What was basically said that after 4 or 5 times of...

lol yes I will have to pull it up for sure. It was actually 20 to 30 feet that it was kicking out the brass, I edited my post.

I only fired 5 here and 13 at the pistol ranger for now. I spent a lot of time looking for my brass, found it all but one. That thing was kicking out the brass about 2 to 30 feet. the cases have dents but more closely like a dent cut from hitting so hard on the upper receiver. When i get...

Hi I took out my new rifle out to see how close the sights were adjusted. The manual said to put the rear site at the 20 and zero at 25 yards. And then after you make the left/right and up/down adjustment, put it at one for 100 yards. The videos I watched some people had to really adjust the...

okay thank you. I see the Lee dies said that they did too. That was the only one that came up. I don't have anything from Lee, I have Redding, Rcbs and Hornady stuff. Thanks again.

I just bought a akm47, which is new. I want to go to the range tomorrow if time permits and site it in. I bought bullets that are brass so I can reload them once I get set up. I just spent the last 20 minutes trying to find what dies to buy. There was a lot of discussions on the dies for...

What brand would you guys suggest?

Two week ago I reloaded using this tool. It was very fast for me lol. I am use to doing everything by hand, this really made it easier.

I have been thinking about buying one of these cleaners. I tumble my brass with walnut shells and although it take hours to clean them. It seems like it is less hassle then these cleaners? I tumble the brass first then start everything else. After I trim and resize, it goes back to the...

Thank you for the reply. I was thinking of where I could do this in the house and then go outside to the garage to seat the bullet. Perhaps I can do it at this desk, the wife would have a fit but, it would be cooler for me for sure. I have been reloading in the summer with a fan on, but I am...

How did you use the feeler guages?

I have a ruger precision I assume the the flat edge in the handrail would be good to level the rifle correct?

This weekend I will work on this for sure thank you all for your help.

Cool thank for the suggestions. I will try that them both.