Search results

That might be the issue cause the necks always comes out with a lot of carbon on the neck I'll give it a cleaning and see if that helps Sent from my SCH-I545 using Tapatalk

Sure I'll give it a shot once I find a range that's a thousand yards near Connecticut Sent from my SCH-I545 using Tapatalk

No the rifle is not a savage it is a custom build by Dave Viers the bullets are seated .0025 off the rifling Sent from my SCH-I545 using Tapatalk

My rifle Sent from my SCH-I545 using Tapatalk

My 338 LM that i just got to shoot right (it was me not the gun) is showing signs of excessive pressure with my reloads i.e. flattened primer and the bolt sticks when extracting. the load i just used is as follows: 3 times fired lapua brass, CCI large mag primers, 285gr hornady match bullets and...

YESSSSSSS!!!!!!!!! I finally got this thing up and running and it was the most stupidest thing you could ever think of, so stupid in fact i would be embarrass to even tell anyone about it…………but i'll tell you anyway cause you may get a good laugh at my expense….so of course the rifle wasn't the...

I emailed dave and he is helping me out but i don't want to send him the rifle cause I'm pretty sure the rifle is not the problem. one thing that he told me is that some times Lapua Scenar don't shoot well and with bergers OTM's they are way to far off the lands if you want them to fit in your...

ok i'll try shooting with a nice gun rest also i'll 300SMK and Hornady 285gr and i'll se how that works.

365 yards

i'm just about ready to sell my .338 LM, i can't get a 1/2" MOA group to save my life, and the very hard part is to admit is that it isn't the rifle it very well might be me. i have tried to tweak the loads. i started with 88-93gr's Retumbo, 300gr laupa Scenar, CCI mag primers, and lapua...

i am looking into an "entry level" NV scope and wanted to know if there are any out there that aren't giant hunks or crap for under or around $1000. Any recommendation? josh

Mostly stove piping and failure to battery Sent from my SCH-I545 using Tapatalk

what are sand cuts? and should i try to polish up the inside of the bushing?

I would like to make my S&W 1911 run like my G17……..i know that a 1911 will typically never be as reliable as a Glock unless you get a Nighthawk custom or the like but i don't want to pay that kind of money……all i am looking for is when a go to the range and beat the crap out of my 1911 it would...

Finally i have got good results for once, @ 365 yards i was able to pull off a 1.57" 4 shot group……the only reason that it wasn't a 5 shot is cause the land owner wanted to take a shot so i figured what the hell. the loads was a 300gr Scenar set .01 off the lands, Lapua brass trimmed to 2.7"...

thanks for all the help I'm going to change up a little and try H1000 instead of retumbo. should i do another ladder test?

the pic below shows my groupings take today, i shot at a range of 100 yards with my 338LM. and i have been having trouble getting the groups better but can't seem to get the right formula for this rifle. here is the break down for today shoot. rifle: 338LM stiller tac 338 benchmark 28"...

Wow that quite a bit of powder for a 338 LM Sent from my SCH-I545 using Tapatalk

A 338 LM pushing a 300 grain bullet with 90 gr of a retumbo what should my velocity be at give or take

rifle specs: stiller tac 338 action 28 inch benchmark barrel with a 1:9.5 twist jewell trigger set at 1# set in a manners T5A stock